Your cart is empty.
Your cart is empty.Product Description
Speed Adjustable Flasher Relay
- CF13 JL-02 electronic flasher relay with standard 3 terminals, for motorcycle and car led turn signals
- The perfect solution for turn signal hyper flashing, fast blinking, not flashing, bulb burnt out warning on the dashboard after installing SMD LED light bulbs
- You can turn the knob at the top of the relay flasher to set your ideal flashing speed according to the LED bulbs load
- Package includes: 1×Electronic LED Flasher Relay
You must know!!!
- PLZ make sure your vehicles stock flasher has the same three prongs and the same (+) (-) positions
- This LED blinker relay may be larger than your OEM and you may need an adapter harness
CF13 Led Flasher Relay
Blinker relay for led lights
- Pin: 3 Pin
- Voltage: 12V (11V-15V)
- Wattage: 0.1W-150W
- Material: High-quality ABS
Simply Plug N' Play
Flasher relay for led bulbs
- As the photo showed, the left side is (+), while the right side is (-)
- Plz check to make sure the prongs and size are compatible!
Adjustable Led Turn Signal Relay
Led Light Flasher 3 Prongs
- Size: Approx. 30×30×30mm /1.2''×1.2''×1.2''
- Replace the factory relay inside the fuse box to correct the hyper flashing issues
Edwin cruz
Reviewed in the United States on January 4, 2025
Bueno
Andy Y.
Reviewed in the United States on August 5, 2024
There is no long initial flash when turning the blinkers on and the adjustment works well. The flashing speed is also not temperature dependent.To make it fit easily WITH NO ADAPTER, you can just pry the top shell of the case off. You have to cut the bottom plastic plate of the shell since there are bumps on the pins which secure it in place. Once the assembly is naked, you can double check and re do some of the soldered connections too if you have a soldering iron available. It has worked fine for me since January, even through the cold snap Colorado had at that time.
ABadPerson
Reviewed in the United States on August 18, 2024
Before even plugging this in, the terminals are loose.The, ceramic maybe? Insulation crumbled when trying to remove the connector from a flasher unit.Would not buy again, this is essentially just a few blade style connectors without any insulation. I'm going to end up using just some blade terminals in the end
Taupe
Reviewed in the United States on March 16, 2024
The media could not be loaded.
Dixson Nava
Reviewed in the United States on October 11, 2024
Buen Funcionamiento
Hyper Speed Media
Reviewed in the United States on January 14, 2024
Relay has fixed the hyper flashing LED bulbs on my Mazda Miata. I was able to swap out the OEM relay with this unit. I needed to make a additional wiring harness to fit it but after that it works like normal.The great feature that it has its ability to change the flashing sequence. It’s very useful because I could dial in the exact timing.It’s been a few months now since I’ve install it and I had no issue with it at all. I would highly recommend it if you are using LED bulbs for your car.
Kendra
Reviewed in the United States on May 25, 2023
I bought those nifty little LED sequential turn signals for my 02 Buell Blast that look like arrows. I had LED turn signals on them so didn't think I'd need to get another relay. The old turn signals were put on 5 years ago and all the LEDs lit up at once. The new ones "chased" each other so only a few were on at a time so when I replaced the turn signals, they didn't have the pull to hit the minimum rating for the old relay. This one works better but the smaller lights (fewer LEDs) still doesn't hit the .02a rating so I'll probably have to add a resistance circuit to them. This does seem to have the lowest amp rating that I've found on Amazon and eBay so it's something to consider if you want nifty LED turn signals.
moth
Reviewed in Canada on March 20, 2023
Good quality
SLick GT
Reviewed in the United States on March 31, 2021
Replaced rear 1157 bulbs in my RV w LED but had the hyper flash. So, replaced the flasher relay (located by the emergency brake/below the fuse box) with this one in all of two minutes. Another minute to adjust the speed. All done. Much improved safety because the LEDs are so much brighter. I haven't replaced the front side turn signal bulbs with LED. (wanted to make sure first this solved the hyper flash--it did)Vehicle: 1995 Ford e350 Econoline RV cutaway chassis (class c). Note: didn't quite fit in my existing relay holder but that was solved with a couple of zip ties.Note: Amazon kept bringing up a 5-pin relay when I typed in my vehicle info. But, I only needed a 3-pin relay. So, make sure you first look at your existing flasher relay before buying the LED version.
Anton
Reviewed in the United Arab Emirates on December 6, 2021
Ordered 2 pcs, one had wires not properly fixed in connectors, another having connectors coming out of the body.
Recommended Products