Shopping Cart

Your cart is empty.

Your cart is empty.

100Amp Trolling Motor Plug Receptacle Set, 2 prong 12/24/36/48 Volt Marine Boat Connector Compatible with 4/6 AWG Wire

Free shipping on orders over $29.99

$49.98

$ 21 .99 $21.99

In Stock

About this item

  • 【100A Continuous Rating】The marine trolling motor plug receptacle are universal design for 2 configuration 12V, 24V, 24/36V, 12/24V, 36V or 48V systems up to 100Amp continuous rating. Compatible with 4/6 AWG large gauge wire without overheating.
  • 【Maximum Durable】 You will see the Corrosion-resistant, Silver-plated electrical connecting pins which have the best electrical conductivity.
  • 【Convenient】Marine plug and receptacle have the best design, which is very easy to use and self-locking. You will feel easy to use this plug because of the ergonomically contoured handle design. This set adopts direct insertion systems. Time and effort saving.
  • 【Safe and Stable】There are waterproof sealing caps and gaskets in the container to further strengthen the waterproof performance, provide additional safety guarantee, and ensure the fastening effect to prevent vibration.
  • 【Visit GaiRen Store】You are welcome to our store to view more about Marine Hardware, like Trolling motor accessories, Bimini Top Fittings, Deck Hardware, Fishing gears, etc.



Product Description

MJ32

Key Features

plug

Ergonomic Design

You will feel easy to use this plug because of the ergonomically contoured handle design. This set adopts direct insertion systems. Time and effort saving.

proof

Waterproof Cap

There are waterproof sealing caps and gaskets in the container to further strengthen the waterproof performance, provide additional safety, and ensure the fastening effect to prevent vibration.

pin

Screw Locking Termination

Very easy to install, fit for up to 4 gauge wire with trolling motor, just loosen screws, put in wire and tighten screws.

Special Reminder:

Make sure the power source is disconnected or, if controlled by a switch, turned OFF before beginning installation of the Plug Receptacle. Failure to remove power from the Boat Wires could cause electric shock.

Q1: Will 6 awg gauge wire work with this?

Ans: Yes, Applicable from 6 AWG to 5 AWG.

Q2: Does this come with plug and receptacle?

Ans: Yes, it comes with plug and receptacle and a set of connectors and screws.

Q3: Can this be floor mounted on a pontoon and still be waterproof?

Ans: Yes, it is IP67 waterproof. It’s waterproof while it’s plugged in and you can cover the female seat with a rubber waterproof cover when it’s not plugged in.

Specification

Rated Current 100 Amp
Rated Voltage 600 Vot
Material SILVER Plated Brass (The Best Electrical Conductivity)
Wire Gauge Compatible with 6 AWG to 4 AWG wire
Waterproof Grade IP67
Mode of Pin Connection Screw Locking
Operating Temperature -40 degrees to 220 degrees Fahrenheit
Times of Plug and Unplug Up to 1000 times

Ghislain Bélanger
Reviewed in Canada on July 11, 2024
Très bonne prise pour mon terrova avec du fil 6 Ga
JG Sutherland
Reviewed in Canada on March 26, 2024
Looks well built, clearly made to last
RWW
Reviewed in the United States on February 18, 2024
I like the way the two halves fit and lock together, this is a very good connector. It arrived on time and it came with everything you need. This is a heavy duty trolling motor connector
Nastassia
Reviewed in the United States on November 4, 2024
1. The way that the plug is constructed, using AWG 4 wires, the screws that hold the wires will only go in so far. That leaves them sticking out far enough so that the bottom part of the plug can barely fit into the top part, with those screws sticking out into the connecting threads, damaging them.2. The screws that hold the wires are just regular philips screws. For the tension that's needed on those screws, the screwdriver will start slipping quite early; the screw heads should've been different - torx, square or hex. Given the size of the wire, the screws are generally too small, and damage the strands3. The plug fits too tight into the receptacle in general. It requires quite a large amount of force to pull it out. That shouldn't be necessary considering there is a latch. The force needed requires the receptacle to be mounted on a surface and with fasteners that will be able to handle such punishment.
Remy
Reviewed in the United States on January 3, 2024
It was well built sturdy just what I wanted easy to install on four gauge wire
Customer
Reviewed in the United States on April 8, 2024
Works great on my new 24v trolling motor, easy installation, locks into place solid, the only room for improvement I can see is the 2 screws that hold the wires into place need some kind of backing plate on them to get a solid connection on the wires, I used a but connector on the wires so the screws could tighten up securely on the wires, other than that it appears to be a good solid product at a fair price
Customer
Reviewed in the United States on April 6, 2024
I bought it to use on a trolling motor. The plug real real big. Ended up not using it. I was afraid I would break it off. But it is built really good. I would say its good for something heavy duty.
JD
Reviewed in Canada on August 19, 2023
Installed on a 4Runner for a winch connection. Makes the installation look OEM.
Mattkins99
Reviewed in the United States on July 26, 2023
I haven’t installed the base in the boat yet but the thing is nice even for the price. I’d have been happy with the quality at double the price but very happy I didn’t have to pay that :-). Mostly metal giving it a quality feel. Yes there’s plastic but more as a cover than structural to the piece. Only two things I would say could be better would be a backplate for the base. I don’t think it will be needed but that would be better. Second would be if it was made in a right angle configuration. Honestly I’m extremely happy with the quality, feel and looks.
DP
Reviewed in the United States on June 14, 2023
Not sure why, but the cap pops off all the time. Does not affect my use case (inside a Sprinter van) but it might affect yours.
Robert V.
Reviewed in the United States on April 12, 2023
This is a great quality heavy duty trolling motor plug. Install can't be any easier. No need to solder or crimp wire into place. Plug has screws to lock wire in receptacles. Screws were a little short for my application, however, Gairen sent me longer screws right away. A++ on Customer services and well as their product.
Recommended Products

$221.52

$ 99 .00 $99.00

4.7
Select Option

$119.99

$ 51 .99 $51.99

5.0
Select Option

$14.22

$ 6 .99 $6.99

4.7
Select Option