Shopping Cart

Your cart is empty.

Your cart is empty.

3pcs Multi-Function DIN Rail Terminal Blocks (2 in 10 Out) with 1pcs DIN Rail Quick Wiring Cable Connector Ground Circuit Terminal Blocks for Circuit Inline 28-12 AWG

4.3 (7) Write Review
Free shipping on orders over $29.99

$7.99

$ 3 .99 $3.99

In Stock

About this item

  • Splicing wire connectors are composed of 3 DIN rail terminal boards, 6 detachable rail clips, 1 200mm aluminum rails and 2 screws. Suitable for building wiring, lighting, chandeliers, sockets, electrical control, household appliances, fan control, etc.
  • Shell material: high-quality insulating material and stainless steel snap ring are used to ensure safe wiring, high voltage resistance, high voltage resistance and long service life. Waterproof, dustproof and heat resistant. Safe and reliable.
  • Wiring range:0.08-4.0mm2;Rated current:32A Rated voltage:600V,suitable for the connection of soft and hard single-stranded and multi-stranded braided wires and solid-core wires,which can connect solid wires (AWG28-12),flexible wires (AWG28-14)and stranded wires(AWG28-12).
  • Usage of DIN guide rail terminal board: Peel off the 10-12mm wire, pull the handle to 90 degrees,insert the wire into the wire hole of the terminal,and lower the handle to complete the installation.High safety,each contact is independent of shrapnel,and different wires are managed separately.
  • Ground Circuit Terminal Blocks is compact and practical in design,and can connect multiple groups of wires,with screw holes on both sides,which is convenient for fixing wires.The spliced wire connector is locked on the DIN guide rail through the solid structure of the guide rail clamp,which is convenient to install


Product Description

ยท

DIN Rail Terminal Blocks

3pcs Terminal Blocks with 1pcs DIN Rail

Ground Circuit Terminal Blocks is compact and practical in design,and can connect multiple groups of wires,with screw holes on both sides,which is convenient for fixing wires.

With all Accessories-Fit all your needs


Splicing wire connectors are composed of 3 DIN rail terminal boards, 6 detachable rail clips, 1 200mm aluminum rails and 2 screws.

Suitable for building wiring, lighting, chandeliers, sockets, electrical control, household appliances, fan control, etc

The video showcases the product in use.The video guides you through product setup.The video compares multiple products.The video shows the product being unpacked.
f

STEP 1

Peel off the conductor skin.

The exposed part is 0.43inch/10mm in length.

a

STEP 2

Unplug the wiring booster handle.

d

STEP 3

Insert the wire into the wire port and press the booster to complete the installation.

dev

STEP 4

Installation completed

APPLICATION

1
ๆˆ‘
d
ww

Frank R
Reviewed in the United States on September 27, 2024
I think these are perfect for lighter-duty applications especially since they took up to a 10AWG wire but they turned out to be a little to light-duty for me. I didn't return them since I may have use for them later. Overall they seemed to be qood quality.
MrB
Reviewed in the United States on September 19, 2024
Received these I'm 2 days. PERFECT TIMING. Wiring 2 sets of fog lights. inverter, stereo, amplifier etc. tl a 6 gang box, these will cut my wiring time by at least 70%. AWESOME PRODUCT
Rashbaugh
Reviewed in the United States on July 1, 2024
Works well. Low profile to fit into tight areas. Functions very well.
Bret
Reviewed in the United States on June 22, 2024
It requires the insulation to be removed from wire to make a connection. It does not make a connection through the insulation
Jeff R.
Reviewed in the United States on May 7, 2024
So far so good. You have to lift the individual wire entry levers all the way up until they snap into position, then insert your wire and push the lever back down. Good buy for the money.
Dan
Reviewed in the United States on March 7, 2024
I tested these with 14awg and 22awg. Both held tight and would not pull out. Tested all the connections for continuity and all were good. I really like the size and form factor for small project DC power distribution. The DIN rail clips are a bit finicky about snapping onto the terminal block, but once in they stay and aren't easily knocked loose. They slide on the included piece of thin aluminum DIN rail, but stay in place on thicker steel DIN rails. Overall I am pretty happy with them and look forward to using them in a few upcoming projects.
Joe Blount
Reviewed in the United States on March 13, 2024
those little springs are fierce. If you let it hit your finger as it snaps back it stings a little!Once the spring is clamped down on a wire its held very securely.The clips to hold it to the din rail do allow it to slide a little, but you have to push on it. It will stay in place fine on its own. So I don't mind that. It can be repositioned if necessary.Overall, a nice usable product.