Shopping Cart

Your cart is empty.

Your cart is empty.

Aftermarket Mats Compatible with 1998 to 2002 Honda Accord Carpet Custom Molded Replacement Kit, 2 Door (801-Black Plush Cut Pile)

5.0 (2) Write Review
Free shipping on orders over $29.99

$191.95

$ 91 .99 $91.99

In Stock

1.Color:2000-yellow Neon Cut Pile


About this item

  • This item is made in 801-Black Plush Cut Pile carpet. The item image may be a different color, but the SWATCH image is the correct color. Carpet Fits 2 Door. Unless otherwise noted, the jute padding is heat bonded to the backside of the carpet and a heel pad is welded to the correct location.
  • Holes may not be cut in automotive carpet and carpet may require trimming to install. PLEASE FIND THE INSTALL INSTRUCTIONS ON THE HELP TAB IN OUR STORE DETAILS PAGE.
  • Automotive carpet compatible with Honda Accord will be Heat and Pressure formed using a form that was created from the original floor pan. Carpet is guaranteed to fit to the floor when installed correctly.
  • All automotive carpets are Made in USA with Top Quality auto carpet materials. IF YOU ARE NOT 100% SURE OF THE COLOR/MATERIAL YOU NEED, PLEASE CONTACT US BEFORE ORDERING.
  • Automotive carpet will fit just like original carpet when installed correctly and is Guaranteed against Defects. This item fits the years: 1998 1999 2000 2001 2002


  • This automotive carpet will be made in 801-Black Plush Cut Pile. Other colors and materials may be available in the selection above.
  • This aftermarket carpet is a replacement for 1998 to 2002 Honda Accord, 2 Door.
  • Carpet will be made with standard flexibe polyethylene backing. Contact us to upgrade to massbacking
  • Unless specified, the jute padding will be attached in the foot area of the carpet
  • Installation may require trimming around the edges and the holes may need to be cut.
  • There is a large variety of colors available. Please request free samples if you want to match a specific color
  • This item fits the years: 1998, 1999, 2000, 2001, 2002, 98, 99, 00, 01, 02

READ FULL INSTRUCTIONS BEFORE BEGINNING - Instructions may vary for multi-piece sets

1. Remove new product from box. Lay flat and pop contours back into place. Allow a few hours for product to relax back into proper shape. Check material for accuracy
2. Compare new and old carpet
3. It may be necessary to use old carpet as a template for console cuts
4. IMPORTANT: Fold new product in half from front to rear. Place in vehicle lining up molded contour to seat risers or any other identifiable starting point on both driver and passenger sides. Once fitted, continue installation
5. Roll product forward make cuts for brackets, shifters vents etc while maintaining proper alignment on seat risers or other starting point
6. Cut in center at firewall to allow product to go underneath dash
7. Continue same procedure for remainder of installation – working your way to outer edges
8. Once product is properly fitted you are now ready to do the final trimmings on outer edges, seat belts and holes etc.

Note: If adhesive is desired, only apply a light brush or spray adhesive after correct dry fit has been obtained.


Gene L.
Reviewed in the United States on August 30, 2022
The of the rug is really good but need patience for the cutting
Edward Estrada
Reviewed in the United States on September 7, 2021
First! Dont throw away your old carpet before you removeAny trim plastics that help line up and hold carpet in placeThis is usually stapled to your old carpetAnd like i mentioned instead of going byAny markings or holes in carpet to help alignThere is nothingI have a manual transmission no cut outYou would think they would cut out at leastseatbelt holesAnyway more of a job than expectedThe quality and the fact that they have jute padding in the bottom areas like factory is great as this build i want maximum outside noise reduction will also be installing adhesive sound deadening under carpetDont look forward to cutting big holes into this carpetAlthough i will have toIm pretty good at this kinda thingAlthough i know many wouldn't like to take on this kind of task since it requires precise cutsTo make carpet ready for installation.Get some razor knifes like the ones they use to cut window tint.