Your cart is empty.
Your cart is empty.Product Description
ron krill
Reviewed in Canada on December 29, 2024
good quality
Frankm5
Reviewed in the United States on September 17, 2023
Nice to be able buy an American made product. Kit came with plenty of hard ware to attach to car to supplement the 3M tape. Also came with cleaner and activator for the glue tape. This is a very complete kit plus some bling thrown in too. I ordered the 3.5 inch kit since my car rides high.Since it it's rather large it has a bit of weight to it but is sturdy and the tape and fasteners will hold it well. I stated from the middle of car and worked way out. I also took a marker and marked the center of the product for a starting point and being sure I'd have enough to do each side. I wasn't sure about how it would look but liking the look now. I occasionally take this car to the drag strip and I actually picked up 2mph at the traps in the 1/8 mile. So not only does it look cool it actually does have some performance benefit. Have not taken a lot highway trip so don't know if or how it may affect gas mileage.
pritpal27
Reviewed in Canada on December 6, 2023
Installation is a bit tougher due to stronger rubber vs the light foam the ezlips use. Had to use additional hardware since the glue didn't stick so well around bends.
William
Reviewed in the United States on July 21, 2019
The All-Fit front bumper lip is definitely better quality compared to other ones I have seen. I actually returned another one to order this after seeing how thin and weak it feels.The installation process was easy, but I just took my time and i really measured out everything before I finally applied the adhesive and stick the lip on. The adhesive seemed pretty strong after installing the lip, however, I did notice some parts didn't stick as good, so, I decided to apply the screws at every 12-15 inches to reinforce the installation.It looks great now, but I am hoping I can find a matching wrap red color for the chrome part of my car. This red is more on the light side.Update:The front bumper lip is holding up every well after installation; it has been 2 months or more now. There was several incidents with deep dip in the roads of LA, California. But no visible scratches on the viewable parts of the lip. The screws definitely help hold it in place during those dip scraping.I wasn't able to get exact matching wrap colors but I got close enough and it actually turned out okay at slightly different shades.I also ordered the side lip after seeing the results of the bumper. I don't regret it at all. The staffs at All-Fit was very helpful and convinced me to give it a try before I chickens out and wanted to returning it.I thank them for convincing me. They also looked into whether my different Mazda design could accommodate the lip. It turns out you can apply the screws onto the side plastic part of the car, for Mazda owners out there. Just don't screw into the connection tabs every 2-3 feet and it will be fine.I'm happy with the lips. I don't think I will do a back lip however. I don't want the car to be too attention grabbing. From the back view, it looks like a regular Mazda. =)
Bruce
Reviewed in the United States on December 21, 2018
There are a few of these products on the market, all claiming to do the same thing. I decided with all fit )Mid lip) based on the reviews. I plan on lowering the car by roughly 1.5 inches, so the mid lip will give it a near slammed look without it being slammed. (Picture is before lowering)Installation was a little trickier than expected, but there was enough extra material to start over again if needed. I have a 1993 Mustang and the first corner had to be redone a couple times, but after that, the installation went smoothly. I recommend pre-fitting and determining where the stress cuts need to be made before pulling off the adhesive backing. There is just enough hardware to secure it in place so you don’t want to lose any. Four out of five stars because the tape would not stick long enough to let me use the screws. I used clamps. The directions say that it is possible to just use the tape but I disagree. After installation the car looks great and I am very happy. I also decided to cut each end of the chin spoiler to match the angle of the inner fender. Otherwise the corner sticks out pretty far and in my opinion doesn’t look as good.
Sean Morgan
Reviewed in the United States on August 13, 2017
Overall, nice product. The package arrived quickly and contained not only the lip, but several nice add ons to make the installation complete including screws and plastic shims to fasten the lip more securely versus the adhesive alone. Also included was an alcohol wipe and adhesive promoter to help the adhesive stick. Lastly a rubber glove (don't want to get the promoter on your hands) and a couple sets of decals in black and white. It really shows that they thought thru what you would need to do a thorough installation. After waiting a couple days for the lip to straighten out in my warm garage, I proceeded with the install. It went relatively easily and the lip was flexible and forgiving enough to go on without kinks. I did cut notches in the back of the lip as directed in a couple areas to make it bend more sharply without kinking. Being a belt and suspenders kinda guy, I did install the screws with the plastic shims as well, so this thing won't come off easily. I can't comment on All-Fit versus the other lips out there, but the rubber material seems to be very dense and strong an should prove pretty sturdy over the long haul. Overall, I am happy with the product and the quality and completeness of the kit. Nice work All-Fit team.
TSG
Reviewed in the United States on February 14, 2017
The product is excellent quality but mine came without any hardware to install it. I didn't want to send it back so a trip to the local hardware store solved the problem.
Recommended Products