Your cart is empty.
Your cart is empty.Kits include two aluminum 3-1/2" x 3/8" dia. pins, two aluminum scuff plates, two flip over style 3/16" dia. Steel clips, and four nuts. Clip flips over stud and locks into place. Over-center action keeps clip in place.
Chalene Baxter
Reviewed in the United States on August 19, 2024
Super easy to install, and the length of the stud was perfect for my 95 4runner
Miriam Huerta
Reviewed in the United States on April 26, 2024
Since they don't come with screws and the plates are pretty plain, combine this kit with "Billet Aluminum Hood Pin Kit Replacement Plates 551444." Normally l'd knock off some points for not including all the hardware, but I knew I wouldn't be using the included plates anyway.You can't beat the quality for the price. If you're looking for a complete kit you'll still need to source out the 8 screws to hold down the plates. The rusty sheet metal screws on my old plates looked like crap so I didn't want the same look. Do yourself a favor and buy the billet plates with recessed screws for an additional $11.
Raymond Martz
Reviewed in the United States on November 12, 2023
Excellent just like I ordered
Anthony Lovegrove
Reviewed in Canada on September 15, 2021
The red pins scratch very easy and should come with screws for the plates very cheaply made .
nicolas
Reviewed in Canada on August 20, 2020
Use it to hold my bumper on my bashbar and it works perfect
Mike Covic
Reviewed in Canada on July 14, 2020
They look awesome and easy to install
Mephiskapheles6
Reviewed in Canada on June 14, 2018
good
JHBL Jr
Reviewed in the United States on January 17, 2017
Since they don't come with screws and the plates are pretty plain, combine this kit with "Billet Aluminum Hood Pin Kit Replacement Plates 551444." Normally I'd knock off some points for not including all the hardware, but I knew I wouldn't be using the included plates anyway. You can't beat the quality for the price. If you're looking for a complete kit you'll still need to source out the 8 screws to hold down the plates. The rusty sheet metal screws on my old plates looked like crap so I didn't want the same look. Do yourself a favor and buy the billet plates with recessed screws for an additional $11.
Ricky
Reviewed in the United States on July 15, 2016
They work great looks good, but the paint chipped a little right away and the metal washer like parts feel too small
Zara
Reviewed in the United States on July 9, 2014
I see complaints about poor quality on just about every other hood pin but these have NONE of thoze flaws. Plates are a little thicker than most.. just abput perfect in my opinion, and the 1/2" posts are plenty beefy for hauling ass off road with, and are machined and anodized with top notch quLity. These make those sparco hood pins look like autozone junk rip offs! Allstar is a fantastic company with high quality and helieve it or not.. honest and legitematd prices. I love em!
CHRIS G
Reviewed in the United States on November 15, 2014
Worst great doesn't rust which is why I went aluminum. But the pins themselves are so smooth even with the studs set so low I have to push on the hood to use them they still slide out while driving. A matte texture on the hood pins probably would have been a better idea.
Patterson
Reviewed in the United States on May 10, 2013
Did an engine swap, the new engine had a different top cross support for the radiator, so the old hood catch system couldn't work properly. My options were: A: spend $200 replacing the hood, or B: spend $12 on these. No brainer.They are actually not that ugly on a 1986ish Jeep Cherokee. I will admit to being concerned abou that, but I, and many other people find them quiet stylish. I mounted them on the outer corners of the two large rectangle sections that make the Jeep hood, but I have seen them mounted on the outermost corner. Prefer the closer mount myself, the outer mount looks ricer-ish. Naturally the Jeep isn't a speed demon, but they have survived a 200 mile interstate drive with no issue. The hood does bounce at highway speed though, probaly and adjustment ussue. No regrets on this $12 fix.
Recommended Products