Your cart is empty.
Your cart is empty.Product Description
Anbull 900W Electric Hydraulic Rebar Bender
Instruction:
- Keeping the switch pressed, the bending block starts to push forward.
- When reach the angle you want, release the switch .
- Loosen the pressure release switch, the bending block reset.
- For starter, marking at the positioning bolt will assist you to bending the angle you want.
Precision steel casting technology
- Bending rebar up to 5/8”(#5)16mm from 0-130 degrees within seconds. The bending block is quenched with precision steel casting technology, durable enough to satisfy your various bending demand and raise your working efficiency greatly
Multiple screws
- Multiple screws fixed on the head enforce the safety and longevity of the rebar bender.
Hydraulic-powered piston
- Hydraulic-powered piston features strong thrust with less power consumption and low noise to extend the service life.
Brushless Pure Copper Coil Motor
- Pure copper coil motor powered by hydraulic pump ensure higher reliability of the rebar bender, which means excellent motivation yet low noise.
Pressure relief valve
- When reach the angle you want, release the switch. Loosen the pressure release switch, the bending block reset.
Detachable Positioning Bolt
- For starter, marking at the positioning bolt will assist you to bending the angle you want.
Notice:
- It is strictly forbidden to bend materials that exceed the specified diameter and strength, so as not to affect the life of the machine.
- The steel bars must be placed horizontally at the bottom of the clamping fixture and make an angle of 90° with the axis of the chuck.
- Loosen the switch immediately after it is cut to the end, and it is strictly forbidden to keep pressing it to avoid damage to the hydraulic bearing and motor
- It is normal for the pump body to heat up after bending for dozens of times. Be sure to let the machine cool to normal temperature before using it to avoid damage to the pump body and seals due to excessive temperature.
- Regularly check whether the screws of the pressure relief valve base are loose and tighten the screws to avoid oil leakage affecting the bending force.
- Replace the hydraulic oil regularly, usually every 3-4 months.
keoni
Reviewed in the United States on March 11, 2025
Totally worth it. You can do precise bends in a few seconds. Not at fancy as the hitachi but you make your money back in 1 job…
Juan camilo
Reviewed in the United States on February 25, 2025
Mu y bien
Justin
Reviewed in the United States on March 26, 2024
It bends # 5 rebar easy. It's worth every pennya
Manny J.
Reviewed in the United States on April 7, 2024
Very good bender, I am very satisfied with its performance and the price. The only problem I've had is getting the brushes, if anyone knows where let me know!!
Robert
Reviewed in the United States on February 26, 2023
Very powerful, bends rebar with ease but green plastic feels cheap and image above shows how cheep.
ScubaGamer
Reviewed in the United States on November 27, 2023
In 10 days did more than 1000 bends, size 3 & 4, grade 60, and about 50 bends of size 5. The tool continues to work without a problem.Two issues that may affect your use cases:1. It is not easy to do multiple bends in one plane2. Harder rebar should be bent in several moves, otherwise the bend frequently breaks .Overall review, extremely good value for the money
Hahn
Reviewed in the United States on October 29, 2023
It worked well, you need to make sure it has oil. One that I received was bone dry.And it cannot bend #6 and #5 was slower.Overall I’m happy especially because of the low price.
Ken & Sharon
Reviewed in the United States on January 13, 2023
We're building a concrete house in a seismic zone so you can imagine the amount of rebar in it. I've lost track of the tons of #3-#5 we've used. Anyhow, we've been using this bender for almost a year now and it is working well. Once you figure out the sequence of bends, it even bends stirrups. We normally use it on a 4x8 workbench but it is possible to bend rebar in place. It's an armful to hold in the air while bending 'in place' rebar, but it does work if there is room to operate it.We did have a problem about a week ago, where the unit just died. The seller took about a day to get back to us, but was helpful with ideas to check. What ended up fixing our bender was the old ' rap the starter with a hammer' technique if you remember working on cars years ago. It's been working fine since.Also, be aware that the bender does not bend the rebar to code. ICBO/ACI specify a minimum bending radius. This bends it sharper which doesn't meet code. This hasn't been a problem for us, even with grade 60 rebar, and I've heard of other jurisdictions accepting it also, but be aware of it, in case your inspector decides to enforce the minimum radius.In all, it works fine and is worth the money. We're happy to have it.
a
Reviewed in Canada on April 27, 2021
bends 2x 15m rebars at the same time, wish it only pivoted on one side though as opposed to both sides as when you're bending a 90deg bar the whole tool moves to 45deg by the time your done
Recommended Products
$22.99
$ 11 .99 $11.99