Your cart is empty.
Your cart is empty. Feature:
1.Gold aluminum shell, small volume, high heat dissipation, high temperature resistance.
2.It is suitable for the installation of heat sinks, and is widely used in doorbells, car lights, elevators, converters, etc.
3.Sufficient quantity to meet your daily needs.
Specification:
Material: aluminum shell.
Dimensions: 60mmx21mmx15mm/2.36"x0.82"x0.59"(L*W*H)
Color: gold.
Rated Power: 100watt.
Resistance Value: 1ohms.
Tolerance: 5%
The Package Contains:
5 x aluminum shell resistors.
Satisfying customers is BokWin's top priority. If you do not 100% satisfied with our products or if you have any questions, you can contact us anytime. BokWin would solve all the problems to your satisfaction. Free Replacement or Refund within 90days.
Joel Chappell
Reviewed in the United States on March 9, 2025
Very good quality. They work great.
Kevin S
Reviewed in the United States on August 1, 2024
This Resistor worked well for my project. It was just what I needed. Good quality part. Resistance was within tolerance.
TedM
Reviewed in the United States on July 16, 2024
These are good quality resistors with accurate values (mine all tested within 2% cold). The actual resistor is insulated from the finned aluminum housing so you can mount them on metal bulkheads/chassis if you want to run them close to their full power rating (thermal paste highly recommended/essential).I'm an EE that mostly works on guitars and guitar amplifiers. I connected one to a 1/4 jack plug and use it as a load resistor for bench-testing amplifiers that are typically around 50W power output and it has worked well. I left the connections bare so I can clip an oscilloscope to the terminals to check the output waveform.Good quality and value, I would buy these again if the need arises.
Jeremy Towne
Reviewed in the United States on March 7, 2024
Works great for what I needed. I will definitely be getting more. When they get hot after awhile the gold color disappears.
ASP
Reviewed in the United States on December 15, 2024
Perfect for my application: I use these for loading my experimental power (audio) amplifiers when testing their power output.Due to cost/performance, I'd buy them again if I needed more.
John Thomas
Reviewed in the United States on November 7, 2024
This is exactly what I need
BeefyCarnivore
Reviewed in the United States on August 11, 2023
I bought these to build a dummy load for testing amplifiers. I've successfully used them for just that and they work as intended.They measure well, with all 5 of them measuring 8.2 ohms on my not particularly sensitive multimeter, which puts them within 2.5% of spec. Beats the 5% they promised.They have taken 60W without blowing up so far, but I don't recommend running them any higher than about 15-20W for any length of time without a decent heatsink.The image is my current mockup of the layout for the dummy load, with two pairs of 4 resistors that can either be used solo (1-8ohm resistor per side, 100W capacity) or in parallel (2-8ohm resistors per side, giving 200W capacity).This should be plenty for most of my commercial amps, but I may have to invest in something beefier for testing Pro amps, like my QSC.I also haven't measured their inductance yet, but the data I got from the measurement looked as expected and helped me prove the impedance independence of my Onkyo receiver (the second image).One of the five came with a terminal on the end that was potted at an angle (bottom resistor in the first image) but it still works fine. Mostly a cosmetic issue, but could make mounting in a metal casing without shorting a challenge.Overall, very happy and blown away for the money.
Honest Abe
Reviewed in the United States on October 18, 2023
Only wish laser printed values were easier to read
Recommended Products
