Your cart is empty.
Your cart is empty.Run multiple lines from one CO2 source. The distributor allows you to split gas supply into multiple lines. Each line has its own shutoff valve.
Charlie Jones
Reviewed in the United States on August 9, 2024
Not much more to say. We had this in our kegerator for barely two months. Yesterday went to grab a beer and nothing came out. Checked the CO2 tank and it was empty. Checked all the hose connections and they were all good. Ended up finding the leak on this manifold where the main body had actually cracked and was leaking from there. No way to fix that unfortunately. Not to mention this one is more expensive than some other options. I thought that may have been due to being of higher quality, but that doesn’t seem to be the case.
sblount
Reviewed in the United States on May 4, 2024
I selected this barbed switching valve so that My wife could switch between her BiPAP and her her 50-ft airline that can reach areas in the house that she likes to work. The important part is that the valve barbs are larger than what would be for an aquarium switching valve.We tried but that didn't work. Didn't supply enough oxygen for her. You have to have strong fingers and I also used a construction needle nose set of pliers to put the airlines over the barbs. Be prepared for a little battle.
Treymeister2005
Reviewed in the United States on November 6, 2024
When turning the valve on and off, a little gas leaks.
Nicholas Jakubowski
Reviewed in Canada on February 12, 2021
Build quality is great, I sprayed the whole thing down with soapy water and didn't see any leaks. Its been hooked up for a week now and I've not had an leaks.Its really cleaned up the c02 lines in my keggerator and made it look much more professional
A Consumer
Reviewed in the United States on September 25, 2020
this is a good manifold. I installed it and it never leaked, great job on getting the fittings tight from the factory. A must buy.
Wanderer
Reviewed in the United States on June 5, 2020
My CO2 tank is plugged into a 4-way manifold. Two are open for things like purging fermentation vessels, kegging, etc. The other two go into my two kegerators. Inside each kegerator is a 2-way manifold going to the two 5-gallon kegs inside. Just make sure to spray with something (star-san, water & soap) and make sure your connections are tightened down completely. They are a simple, intuitive design and they just work. Great value.
CK
Reviewed in Canada on January 7, 2020
I grabbed one of these co2 manifolds to help setup a friends beer brewing room and since Bev Rite is a well-known brand I bought this without question.Right off the bat when you hold it, you'll feel that solid weight as it’s a nice fat tube of aluminum so the walls are pretty thick. Just like with anything that deals with gas to check for leaks first. So what I did to check for leaks was to plumb this up to just an air compressor, turned off all the taps, throw it in a bucket of water and gave it a couple dozen psi.I didn't have any issues with the valves they were spot on however the end plug was letting a bit of bubble out. Disconnected the compressor, dried off the valve, removed the end plug, cleaned out the old sealing material (looked like pipe compound), gave it a few wraps of a nice teflon tape.Hooked everything back up, threw back that psi level and it held just fine.I gave this 4/5 stars as it is a great value compared to local prices. It would have been 5 stars if it were not for that end plug issue. Kind of annoying BUT an easy fix.TIP ► For safety such things should always be psi tested first before you use it for your intended purpose as it is just so easy to do. This is a good rule of thumb to get into a habit. Yes, anything brand new 'should' work just fine however we cannot 'see' a gas leak as we can with water. At times lost cylinders of co2 gas can be prevented by checking the connections first.TIP ► Cannot throw something like this in a bucket of water? Then make a soap solution and brush that over all the joints. If you have a leak you'll see the bubbles form right at that exact spot. Always check gas related products !Helpful, is how I hope you find my review
ARTURO
Reviewed in Mexico on July 31, 2019
Cumple su objetivo
Alejandro G.
Reviewed in Mexico on July 28, 2019
Producto perfecto, no presenta fugas, funciona correctamente
Ubaldo Arriaga
Reviewed in Mexico on December 19, 2019
Excelente producto y calidad, ya instalado en mi Keezer Casero para dispensar 4 lineas
AutoExec
Reviewed in the United States on September 28, 2016
This manifold was exactly what I was looking for and worked wonderfully. I purchased a full sized kegerator from a friend with the idea being that I would use the kegerator for dispensing homebrew. Most homebrew batches are 5 gallons which means that I can store, easily, 2 5gal kegs in the kegerator but I only have room for one CO2 tank. The manifold works to allow both kegs to carbonate at the same time.When it arrived, I used double sided foam tape and two small screws to attach the manifold securely to the inside of the kegerator. I would suggest using air line specific hosing, and follow the diameters exactly. When done so, it does take some elbow grease to attach the line to each of the barbed fittings. Although, technically not needed, use some hose clamps as well.I used this manifold in conjunction with Ball Lock style connectors which does allow for additional sealing when one connector is not hooked up, but the ball valves attached are great for closing pressure while initially connecting the air line. The ball valves do not act as regulators, and should not be thought as regulators. Instead, they simply open and close pressure to the line. To regulate one line independently, you would need to have a separate regulator on the line.Eventually, I may upgrade with independent regulators, but for now I am very happy with this purchase.
belowi
Reviewed in the United States on May 5, 2016
I just received this today so time will tell, but so far I am very satisfied. I had only read the other reviews after I purchased it from Draft Warehouse via Amazon, it arrived today only two days after my order was placed with standard shipping. Upon opening the package I partially disassembled the manifold by removing the inlet barb and end plug to check for any oil or metal shavings but I saw none and a rag ran through the body of the manifold came out clean, I don't know if mine was from a different seller than others who were complaining of theirs being dirty, but mine was clean and ready to go out of the package. Other reviewers had mentioned there being cleaning recommendations shipped with theirs but I did not have any. Anyway, I applied a bit of RectorSeal #5 to the screw fittings I had removed, attached my CO2 line and submerged it in a water bath to see if there were any leaks. None. It is now installed so I'll update if I notice any leaks or longevity issues, but so far this looks like a great bargain.
Horselain
Reviewed in the United States on April 26, 2016
I purchased this CO2 manifold when converting my single tap kegerator to a double. After reading the online reviews I was a bit skeptical due to complaints with metal shavings and leaks, however 1 year later everything has been working fine so far. I didn't take it apart and clean it when I first got it, but only due to pure laziness on my part. Probably not too difficult if I wanted to put in the effort. No leaks so far and for the price you can't beat it!
Recommended Products
$18.38
$ 7 .99 $7.99