Your cart is empty.
Your cart is empty.With its own air supply, this popular remote cooler can literally be mounted almost anywhere, making it a popular addition for performance compacts, hot rods, muscle cars and trucks. An efficient 16 pass tube and fin cooler coupled with a Tornado fan and aluminum brackets, built with -8AN male fittings and includes 2 each -8AN x 1/2 inch barb fittings. With the large -8AN fittings this cooler was designed primarily for engine oil applications, but also can be used for heavy duty transmission or fuel cooling.
Customer
Reviewed in the United States on July 14, 2024
Works great. all parts needed to plumb this aftercooler on on air compressor can be found on Amazon
networkguy
Reviewed in the United States on February 7, 2024
As others, I'm using this as a precooler for an air compressor, and it gives about 150 degrees of temperature differential. Fan isn't the quietest, but with an automated on/off switch it isn't noticeable when the compressor is running. It would be better if the Inlet/outlet ports were supported due to the size of the fittings and low strength of the tubing to resist installation torque (yes, backup wrench is required and is warned about in the instructions, but the design could be a bit more rugged).
Paul Eddins
Reviewed in the United States on December 21, 2023
Installed in line to condense out water before compressed air goes into tank. Dropped temperature from 280 degrees down to 70.
Kizmit99
Reviewed in the United States on February 14, 2022
I'm using this as a cooler between an air compressor pump head and storage tank. Air leaving the compressor head is *very* hot, when it leaves the intercooler it is basically room temperature (likely a 150 to 200 degree F drop). I have the fan setup to run whenever the pump motor is activated. The fan and intercooler come pre-assembled and I was able to use the brackets directly for mounting the unit. I am pleased with the unit, but I do wish it came (or was available with) a variety of AN-8 mating connectors - the barbed fittings weren't applicable to my use case.
Rick
Reviewed in the United States on September 23, 2021
I wired an 8 Amp 120AC to 12V DC converter to the pump motor so the fan on the cooler only runs when the compressor is running. This cooler is plumbed between the compressor head outlet and the storage tank inlet and reduced the temperature 113.5 degrees F in its initial run from 0 PSI to 165 PSI. I have an auto-drain moisture trap between the cooler outlet and the tank which removed 2.5 oz. of water! I am VERY pleased with this coolers performance and construction.
barron
Reviewed in the United States on November 9, 2021
Great product made here in the US. Not a single fin is damaged and I bought 3 of these. Amazing product quality and packaging was good with getting it to me in that condition. Using them to cool video cards. Will be buying a couple more to cool power generators.
luis
Reviewed in the United States on December 16, 2020
Spend your money somewhere else, this cooler doesn't really help at all.my temperature keeps rising to 220 if not higher, I even took my Jeep to a shop so they would go through my setup to make sure I did everything right and everything on my side was done correctly.what a disappointment...
Customer
Reviewed in the United States on October 6, 2020
My transmission is going on 35 years old. To give it a fighting chance to go another 35 I replaced the anemic stock cooler with this. I have a temp sensor both before and after the cooler to see what sort of cooling it offers. On a cool morning while towing a small trailer up a slight incline, I saw it cools 30 degrees without the fan running. (Fan doesn’t kick on till 185 ish)Cheap insurance and even if the trans give out, this can always go in my next truck.
Recommended Products
$52.99
$ 26 .99 $26.99
$32.50
$ 16 .99 $16.99