Your cart is empty.
Your cart is empty.This transmission shift boot matches the fit and function of the original equipment boot that as become damaged or missing. Made of quality materials, this boot is designed for durability and has been validated for a proper fit.
Honest reviewer
Reviewed in the United States on September 25, 2024
My shift lever boot had torn apart years ago and I never got around to replacing, and I didn't really want to have a dealer install ($$$).Looking on Amazon, I settled on the Dorman 47106CD version, as the description indicates it would fit my 2002 Silverado 2500HD.I watched some you-tubes to see what was involved and it didn't look too hard, although I could not get one screw to unthread when removing the steering column cover. Nonetheless, I could spread it enough to remove the old boot.Installing the new one proved to be a pretty good challenge and I worked up a pretty good sweat. I didn't have anything to use as a lubricant to slide the new boot over the shift lever, and I didn't want to try and figure out how to disassemble that. So I slowly worked a little bit at a time to slide the new boot over the shift lever. I was really concerned that I would tear the boot, or it would get too stretched and not have a snug fit, but after an hour or two wrestling it a little bit at a time, I got the boot all the way on. Next challenge was getting the metal base to snap into the steering column cover, but I did and then snapped it into place.The new boot looks just as nice as the original and despite all the stretching, still fit snug with no tears.
Alfonso Galindo Cisneros
Reviewed in Mexico on August 5, 2024
Funciona bien pero le falta un poco más de calidad.
Jake S.
Reviewed in the United States on August 1, 2024
I’m not very happy with the quality. Dorman is normally a reputable brand. I installed this 2 days ago and the rubber is already splitting.
Tim Clark
Reviewed in the United States on July 29, 2024
Shift column boot was tore. Put a little silicone grease around inside of boot and it slid right on. Dorman replacement parts are the best. Took less than ten minutes to install
GSPChaser
Reviewed in the United States on June 4, 2024
Fits pretty well, though a bit short, so it slides in it’s opening when shift lever is moved through its maximum range. Works well enough, and looks good. Hope it lasts. Good value compared to OEM.
JOSE HUGO CERVANTES LOPEZ
Reviewed in Mexico on March 20, 2024
EL PRODUCTO LLEGO EN TIEMPO Y DE CALIDAD, GRACIAS
JustMy2¢
Reviewed in the United States on May 26, 2023
My Sierra will be 21 years old in November. The shift boot has been torn for 20.5 of those years. When the Tow/Haul switch went out; I disassembled the steering column cover to repair the wires for the switch and decided to replace the boot while everything was disassembled. It arrived from Amazon a day early, it took all of five minutes to attach the boot. Within 15 minutes everything was back together, looking good , and working. The Dorman™ price was around $10 less than other sources, and when you install it correctly, there is no possibility of tearing the piece. Lube gel? Really?
David
Reviewed in the United States on March 8, 2023
Fit great. To get it to slide on easily, I ran it under hot water for a bit which made it more stretchy. I wanted to avoid tearing it during installation. Worked great.
ANTONIO TGDA
Reviewed in Mexico on February 21, 2023
Quedó muy bien en mi 2001 chevrolet silverado 1500
Henry
Reviewed in the United States on November 1, 2023
Old boot was torn on my 01 2500 suburban. This one fit perfectly and was easy to install. 1 month and 3000 miles later, still looks new.
Tom B.
Reviewed in the United States on September 20, 2022
After watching numerous videos, and tearing one of these attempting to install it without the proper lubricant, I will share the easy way to install this part. Some of the videos showed having to take the dash bezel off, the plastic clamshell around the steering column off, and then removing the gearshift lever. Even doing that, will not work if you have a gearshift with the tow haul mode button on the end because you cannot get the wire through the rubber boot without digging into the column and disconnecting the wire.After tearing one of these boots attempting to slip it over the end of the gearshift and using a silicone spray, I decided to use O-ring lubricant. I previously purchased a bottle off of Amazon and it is a silicone based grease which actually helps preserve the rubber boot.First, remove the old rubber boot by tearing the pieces off, and then separate the upper and lower clamshell cover of the steering column by gently prying them apart with a screwdriver or other non-Maring plastic prying device. You will only need to separate The upper and lower pieces about a half inch. The lower piece should be the one that drops down slightly. With the pieces slightly separated, you can now remove the rest of the boot base. Now, apply a semi liberal amount of the silicone O-ring lube to the inside of the gearshift boot. Also, apply several drops to the top of the gearshift lever and smear it around so the entire section is covered particularly towards the end of the lever. Slowly slide the gearshift boot over the end of the gearshift lever. Do not force it and go slowly. Slide the boot the remaining way down the column and then position the gearshift boot base into the slots of the upper and lower Console clamshell. Snap the clamshell pieces back together and position the end of the rubber boot into the groove into the gearshift lever to seat it. Be sure to wipe the residual O-ring lube off your gearshift lever. Hope this helps.
Joel martinez
Reviewed in Mexico on December 27, 2022
buen articulo
edgar dario
Reviewed in Mexico on October 2, 2021
La membrana central es flexible y el marco del borde es rígido para conservar la forma.. buen producto
Recommended Products
