Your cart is empty.
Your cart is empty.This replacement engine coolant thermostat housing is engineered to match the fit and durability of the stock thermostat housing on specified vehicles. It is designed to withstand extreme temperature changes to extend service life. Vehicle model years this part fits (be sure to check your vehicle trim using the Amazon garage) - [Acura CSX: 2006, 2007, 2008, 2009, 2010, 2011] - [Acura ILX: 2013, 2014, 2015] - [Acura TSX: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014] - [Honda Accord: 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012] - [Honda Civic: 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015] - [Honda Crosstour: 2012, 2013, 2014, 2015] - [Honda CR-V: 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014] - [Honda Element: 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011]
Propman420
Reviewed in the United States on March 5, 2025
great value and direct fit !!
David Andrukonis
Reviewed in Canada on May 31, 2024
everything lined up perfectly . Just remember to cut 4MM off the factory thermostat mounting bolts or add washers so you don't brake the new plastic housing or pull out the brass inserts
Derrick Rogers
Reviewed in the United States on March 26, 2024
Everything went fine with the install except if you are using the OEM Honda bolts you will have to drill out the bolt holes in the housing because the bolts are too long. Other than that great fit with no leaks.
bimmer man
Reviewed in the United States on February 24, 2024
Well I’ve only been looking for the right thermostat housing for a month almost for my 2007 CRV they sent me the right thermostat cover with thermostat every time but every time I ordered a thermostat housing for a 2007 CRV it didn’t fit the thermostat cover. I kept trying to figure out from the picture if I was getting the right thermostat housing but there are two different housings. Every time I ordered one it was the wrong one but finally I ordered this one and it was the right one so if you’re having trouble finding a thermostat housing for a 2007 CRV this is it
Pappy T
Reviewed in the United States on December 25, 2024
Worked great on my 2009 Honda CRV
David Payne
Reviewed in the United States on November 25, 2024
Thermostat Housing worked great
Jonás García filpo
Reviewed in the United States on October 28, 2024
Bien
K. Laforest
Reviewed in Canada on January 4, 2024
Worked great, shipper delivered so I didn’t have to go pick it up
JULIO
Reviewed in the United States on July 5, 2023
Hola gente! La pieza es buena vale para CR-V 2010 como lo describen.Tienes q ser algo mañoso para abrir los agujeros con una broca finita y luego haciendo rosca , hasta q pase al otro lado, para q pasen los tornillos originales, o no!Los míos originales estaban muy oxidados, así q decidí meter otros de la misma rosca pero más largos y se quedó como en la foto. Un saludo a todos.
Paul
Reviewed in Canada on May 31, 2023
Honda screws are too long, I drilled out brass inserts and plastic for longer Honda screws, tough getting access to two holes. Drilled just big enough so as not to ruin threadsas I had to drill from front side. Buy Dorman screws if they have! Fits good & works great though
Page
Reviewed in the United States on March 2, 2023
paid twice to get the job done because you can’t tighten the bolts all the way to seal the housing and the thomstat reasons been the holes blocked off you have to drill them out then tap the holes! After the first time,don’t make the same mistake like me! Good luck.
mark aalders
Reviewed in Canada on April 6, 2023
Bolt holes for thermostat are not all the way through ,oem bolts too long ,maybe use Dorman thermostat
Crishell
Reviewed in Canada on December 5, 2019
Fit perfectly with my honda crv 2008. It comes with a gasket.
Recommended Products
