Your cart is empty.
Your cart is empty.Product Description
Ready to Troll
Slow your boat to the ideal trolling speed with the EasyTroller trolling plate. Rugged aluminum components and hinged plate design help prevent damage to the plate in case of accidental acceleration. Models available with or without fins.
The EasyTroller difference
Eliminate damage caused by accidental acceleration
Under power, prop thrust can bend or damage the typical trolling plate as water is forced upward.
EasyTroller flexes under pressure
The EasyTroller trolling plate flexes to divert the prop thrust downward, preventing damage to the plate.
Hydrofoil fins combine two products in one
Choose a model with hydrofoil fins to improve your hole shot and help prevent porpoising.
Using EasyTroller
- Tie off the release cord with enough slack for plate to go down and prop to turn
- Pull the cord and the plate will move into the down trolling position
- The plate will lock into place when properly seated, slowing the boat’s trolling speed
- Release the EasyTroller plate by pulling on the cord with the motor idling and in forward gear
- Accelerate slightly and the plate should raise and lock into the up position
Proudly made in the U.S.A.
- EasyTroller Standard Model fits outboard and stern drive motors 50-300 horsepower
- EasyTroller Short Model fits outboard motors 30-45 horsepower
- Reduce trolling speed to as low as 1 mph
- Hinged plate flexes upward to prevent damage to the plate
- Manufactured from marine-grade anodized aluminum and stainless steel
Don't forget!
- EasyTroller should always be in the up position when running at speed
- EasyTroller should be set in the down position when transporting your boat on a trailer
Installing the EasyTroller
- Can be mounted on top or underneath the cavitation plate
- Position the EasyTroller 4-7 inches from the prop, then clamp in place
- Drill 5/16" holes through the cavitation plate and mount with included hardware
Mounts under or on top of cavitation plate
MIKE S
Reviewed in the United States on September 12, 2024
This product arrived on-time, as-specified, and is very well built! I would recommend it to all who are looking for a solid, easy to install, trolling plate for their boat.
William Neale
Reviewed in Canada on August 20, 2024
First time out this part failed. Can I please get a replacement part?
Shane
Reviewed in the United States on July 7, 2024
Works great. We have 1 on each boat
Jeremy Herzog
Reviewed in the United States on October 24, 2024
This trolling plate was exactly what I needed to get my 20ft Grady White Tournament to troll at my desired speed. It brought my idle speed from 2.8mph down to .8 mph. With just a little throttle I’m right where I need to be at 1.7 for walleyes.
Denis
Reviewed in Canada on September 18, 2023
Good quality product and easy to install.
Andy schultz
Reviewed in the United States on July 14, 2023
I installed this on a 19 foot Bayliner and it was easy to install after removing the lower unit. It works so well trolling and the trim plates make it plane fast and more controllable.
Customer
Reviewed in Canada on September 22, 2022
Great product, works as it should.Very happy. Would give it 10 stars but it would only let me give 5
Tim
Reviewed in the United States on May 30, 2022
I'm really impressed with the Easy Troller. I have a Mercruiser 3.0 I/O. Have always been frustrated that I couldn't troll due to high speed. Crank baits would be just below surface. Just had Easy Troller installed, and it cut the speed way down. Baits get down like intended. I also purchased the optional wings. Gives better hole shot by keeping the bow down at launch. Easy to use. Goes down and back up with simple pull of rope. Can't wait to get out fishing!
john hobbiest
Reviewed in Canada on April 10, 2021
Will try to get the boat out soon to see how it performs on the water.
Heidi
Reviewed in the United States on July 17, 2019
I have a 21' bayliner capri with an I/0 240hp engine For years I primarily used it as a ski boat and to pull the kids tubing. I love to fish, but certainly could not troll with this boat. I decided to try the EasyTroller plate. It worked perfectly and I am thrilled to now be able to troll for Kokanee and Rainbow trout. Lowered troll speed from 2.5-3 mph to 1-1.5 mph. However, I did put the plate under unfair stress a couple times on the lake one day. I put it in the up position to move locations on the lake and hit it hard (24-30 mph) and made several sharp turns. The third time I did this, when I went to put it back in the down position to begin trolling, the lower section of the plate was just gone. The company responded quickly and professionally and sent me the parts to replace (lower plate and pins, no charge) and I was able to fix it myself. Now, when I want to use the boat for a day of skiing/tubing, I simply remove the four bolts and take the plate off - no problem! I would highly recommend this trolling plate and the company that sold it thru Amazon!
Karostay
Reviewed in the United States on July 14, 2019
Received my Easy Troller on Wednesday 7/10/19Installed it 7/13Reason why I bought this product my 50Hp Merc Big Foot i just bought would only troll down to 3.5 to 3.8 MPH a bit fast for my style of trolling.Reading the reviews by previous posters had all the right answers35 years as a Tool and Die maker I was impressed just how well this product is made.Sturdy great finish well thought of product.Installation took around 20 minutes simple, Drill a few clamps two 1/2 wrenches.Then the test at idle my boat was running 3.7 MPH .I pulled the cable the plate lowered just as designed and my speed dropped to 1.3 MPHI actually had to give it more throttle.Boat handling was perfect.When I was done trolling I pulled cable gave a little throttle the plate returned to where it belonged and off I went full speed . I bought the one 50 hp to 300 hp with the fins the price at the time was the same
Customer
Reviewed in the United States on September 28, 2016
The product works very well ... Is solidly built and was quite easy to install. My only gripe would be that some of the edges of the 1/4" alum plate were sharp as they did not appear to debur the material after it was stamped out ... Lost 2 salmon spinner and diver set up first time out as these sharp edges made short work of my fishing line.
Recommended Products