Your cart is empty.
Your cart is empty.From the leaders in Z-wave plus technology, the Ecolink Motion Detector allows you to improve the safety and security of your home and family easily and effectively. Built with premium components for better performance, these motion sensors provide instant and reliable performance as part of your security system. Ecolink is a leading developer of low power, highly reliable wireless solutions, including a wide range of intelligent wireless security, sensing and home automation devices. Dimensions: 3.5”L x 2.3”W x 1.8”H.
Sean Thomson
Reviewed in the United Kingdom on March 20, 2024
I cannot test this as the unit is not compatible with UK/EU Z-Wave networks. Unfortunately, the frequency was not mentioned in the description when I purchased it. I would buy it if a UK/EU version was available.
Carolina Mosiño
Reviewed in Mexico on July 23, 2020
Llegó incompleto, ya estoy viendo la devolución
Mike
Reviewed in Canada on November 20, 2019
These are great motion sensors. Paired up very quickly with Smartthings hub and work great. Very quick and responsive. Great battery life so far. Used to have all Zigbee sensor that would constantly disconnect and these Z-Wave sensors are much better.
Michael
Reviewed in Canada on February 9, 2018
I bought this device to use with my SmartThings Hub and it works perfectly. Its main purpose, at the moment, is to turn the living room lights on dimly when someone comes down the stairs between 12am and 6:30am. Right now this is for middle-of-the-night baby feedings.I had no issues pairing it to my hub and it works very well, almost instantaneously, for its intended purpose. Will most likely purchase another one in time.
Aldo E
Reviewed in Mexico on January 29, 2017
Funciona muy bien y la duración de la batería parece que va a durar mucho. La conexión con SmartThings fue rápida y salvo por el problema de que su tiempo de refresco es mínimo cada 5 minutos.
JB
Reviewed in the United States on May 2, 2015
The "Ecolink Z-Wave PIR Motion Detector, Pet Immune (PIRZWAVE2-ECO)" has been running in my home for just under 5 months and has been doing a bang-up job with little to no complaints by me.It is a standard-sized format Z-Wave enabled motion sensor which I have paired with my Raspberry Pi/Domoticz z-wave home control setup. Pairing was simple: insert the battery and switch your z-wave controller into inclusion mode. It was found immediately with no issues and is reported in Domoticz (OpenZWave) as two separate sensors: the motion sensor and a tamper switch. The tamper switch is simply an on/off switch to advise when the case has been opened.The sensor is corner-mounted in my entry hallway approximately 9 inches (~22.8 cm) from the ceiling and points towards the kitchen/living room area however, as it does have a wide field of view it covers even the bedroom door areas. From its location it points down the hallway and through the galley-style kitchen and on into the dining area with clear line of sight; a total length of approximately 32 feet (~9 3/4 meters). I have the unit set to the highest sensitivity (a simple jumper connection within the unit changes this) which detects even a small movement at the far end of the dining area.Keep in mind the sensor is hard-coded with a 4-minute cycle time meaning it turns on then remains in the current state for 4-minutes before checking again. For me it is no issue however if you are looking for a smaller time frame this is probably not the unit for you. It also reports battery level and after just under 5 months my unit is still reading 99%. Not too shabby.I have my system set up to activate a hall light when movement is detected (only after dark and only between a certain time period) and it works like a charm. There is a slight delay of approximately 1-2 seconds at times though I believe that is due to the large distance between the motion sensor and the Z-Wave controller - the signal needs to be repeated to and from the controller to reach the unit. If I set up a light as a slave device the delay almost completely disappears.Overall, this unit suits my setup almost perfectly and I'll be purchasing a few more in the near future to automate a few more lighting scenarios.
Carl Saltzberg
Reviewed in the United States on February 5, 2015
WINK Hub compatibility review: This sensor IS compatible with the WINK hub (as of 2/5/2015). To pair it to your system, first go to the wink app then select [ wink hub > settings > z-wave > inclusion mode ] then set the ecolink into inclusion mode (must be after the hub) by inserting the battery or inserting a paperclip into the hole in the back cover.Pairing was a breeze with the WINK hub, detects motion and can trigger a resonce in less then a second, I have it set to turn on porch lights.On the WINK hub this can be used as a robot to only DETECT motion by not the absence of motion, ie it can NOT send a new signal after a time of detecting motion to TURN OFF your lights ect. There are some work arounds (tripper, ifttt) but as of (2/5/2015) WINK has no native timing option in there robots. You could set the light of interest to every (10min or an hour) set its level to the "default state" and then the sensor when tripped would change the light to your programmed setting, then after a period of time and the scheduled program activates it would "reset" the light.General review:Pro's: This product is well built and looks good, (it looks cheap in its picture). It comes with a battery and mounting equipment for both flush on the wall or in a corner (but not able to adjust verticle angle, probably not an issue as it it built to look down). You can set an optinal sensitivity level to ignore small or large pets.Con's: no adjustible positioning arm. Limited choice of a 10 second OR 4 min delay (once motion is detected it will turn off for that long before turning back on and checking for motion). This may or may not matter depending on your application and the program you use to interpret motion signals. Delicate back pannel, use a flat head screw driver and gently push the clip up then pull the back panel away (cautionary not: the equipment board is attached to the back pannel).
Recommended Products