Your cart is empty.
Your cart is empty.FelPro gaskets offer 100% vehicle sealing with applicationspecific materials to give you sealing solutions with the performance and durability professionals trust
Customer
Reviewed in the United States on February 15, 2025
As adve
Carlos Guadalupe
Reviewed in the United States on August 26, 2024
These worked Perfectly to seal my oil leakage from back of valve cover mine was leaking on the driver side, used on 1969 c15 GMC with 1976 350 SBC. Definitely recommended, these are rubber with steel bolt hole inserts installed without any issues no more oil leaks!!
Henry A.
Reviewed in the United States on August 19, 2024
These are a nice upgrade from the leaking gaskets on my 1984 5.7
Customer
Reviewed in Canada on March 24, 2024
I couldn’t get these gaskets to seal on my 350 Chevy with aluminum valve covers. Kept changing things around but no luck. My previous rubber gaskets worked great but I thought I would take it to the next level. I didn’t work!
Travis G.
Reviewed in the United States on November 13, 2024
Very Nice
surrndr
Reviewed in the United States on November 5, 2023
I like that these are reusable. So far so good. No leaks. They do have to be installed a certain way. Instructions are easy to understand. I would purchase them again
ROBERT GAGNON
Reviewed in Canada on January 20, 2023
AAA+++ THANK YOU
Gary
Reviewed in Canada on August 22, 2022
You dont need these gaskets on a 305 GM . The GM blogs tell you to just use a good sealer on the cover and put it onHowever these are good gaskets and include the bolt plates.
Dr. B
Reviewed in Canada on May 19, 2022
If you don’t want to use sealant or glue this is the best gasket. I just replaced the set I installed 9 years ago because they were getting hard and starting to weep. Not bad!
Danny New
Reviewed in the United States on March 9, 2022
Excellent small block Chevy gaskets. The value cover helper keepers are much bigger than stock. They will fit a Chevy 327 also tho it's not listed. Be careful and look for the extremely small (pushrod side) stamping on them. They actually have a specific way to be installed. Just don't install them any ole way. Will last for years and are reusable.
Nicholas S.
Reviewed in the United States on July 3, 2020
Perfect fit for 77' Corvette with GM 5.7L V8 350 Small Block Engine.I replaced the original 1977 Factory GM cork gasket that was crumbling and leaking like a sieve. Even a little bit of oil spread out across an engine looks like a ton. Remember to clean lifter arms / valves from visible build-up and crud / gunk while you have the covers off.Parts cleaner works great at freeing crud and evaporates quickly. I used rags and flat blade screwdriver to clean of old gaskets prior to installation. You want mating surface of valve covers nice and clean for new gaskets. I used a Shop-vac and rags for vacuuming and wiping up any leftover crumbs from the old cork gasket and clumps of grease buildup crud. If valve covers aren't new, use a small hammer to bang out any dips in metal around bolt holes from over-torquing covers prior to installing gaskets. I applied a thin coat of 3M weatherstrip adhesive to the bottom of the valve covers to hold them in place while installing. Don't go overboard with the 3M weatherstrip adhesive or whatever you use, the Fel-Pro gaskets do the job at sealing and the adhesive is simply holds them in place while installing - less is more. When re-installing, don't overtighen bolts, next check for leaks and if there's no leaks then you installed it properly. Fel-Pro is good as gold!Tip: For old valve covers, now is the best time to spray them down with degreaser/soak them in Evaporust and give them a fresh coat of paint prior to putting on the new gaskets and re-installing.
Jonathan Arrieta S
Reviewed in Mexico on June 22, 2019
Buen juego de juntas. Se ajustan a la perfección a las tapas de puntería.
The End
Reviewed in the United States on December 11, 2012
these gaskets rock! still to this day the area around the valve covers is dry as a bone. no more oil wicking thru the cork type of gaskets. make sure when you install them you mount them correctly. there is an up and down orientation. pricey but very worth it!
Recommended Products
