Your cart is empty.
Your cart is empty.
Motor
Features:
4 poles 12 slot Hi-torque motor design.
CNC machined 6061 T6 billet alumium heatsink can.
High purity copper windings maximizes efficiency.
High RPM ABEC5 oversized bearings.
Universal fits 1/16 1/18 brushless cars-multi-mounting system for M2.5 screws.
Precision balanced rotor, smoothness for best reliability and maximum RPM.
Stator - Super Thin (0.35mm) laminations.
Removable/replaceable.
Precision engineered for maximum energy conversion.
Specification:
RPM: 4800KV
Max Current: 24A
Max Watts: 300W
Can Size: 2435
Sensored: No
Can Diameter: 24mm
Can Length: 35mm
Shaft Diameter: 2mm
Shaft Length: 12mm
Bullet Connector: 3.5mm
Weight: 58.3g/2.1oz
Max voltage: 7.4V(2S))
Electric Speed Controller
Features:
Compatible with sensorless brushless motors.
High anti-interference capability.
Using advanced software interface to set up or update the software.
Super smooth and accurate throttle linearity.
Fast response to throttle input.
Mutiple protection features: low voltage cut-off protection, over-heat protection and throttle signal loss protection.
Specifications:
Cont. Current: 25A
Burst Current: 90A/10sec
Battery: 2 Cell Lipo / 4-6 Cell NiMh
BEC: Yes
BEC Output: 5V/1A
Power Supply Plugs: T Male
Motor Plugs: Female 3.5mm Bullet Connector
Size: 40*27*15mm
Weight: 29g /1oz
Package size: 10 * 8 * 6.5cm/ 3.9 * 3.1 * 2.5in
Package weight: 116.8g/4.1oz
Package list:
1 * 2435 4800KV 4P Sensorless Brushless Motor
1 * 25A Brushless Electric Speed Controller
J. Rapp
Reviewed in the United States on May 29, 2024
Based on pictures and reviews, there appear to be a couple different variants of this setup.The one I received had the capacitor mounted on pins rather than some of the pictures which either show no capacitor or what looks like a pair of capacitors mounted on wires and heatshrink wrapped. This is the one part that seems the most fragile, though would be easy to repair if the pins broke. But I'd certainly have preferred a version with the capacitors mounted on wires or no capacitor at all.It ships direct from China, but I found the shipping and delivery time to be quite prompt. Maybe a week at the most.I had to modify my motor plate to fit the motor. Was a simple dremel job. The widest holes are about 13.9mm inside-edge to inside-edge on this motor vs about 14.3mm inside-to-inside on the stock traxxas brushed motor.There are a lot more wires to wrangle than with the stock setup, and I'm a bit of a neat freak but I'm pretty happy with how I got everything lined up.Out of the box responsiveness seems quite good. Will probably pick up the programming card, but running with a 2S 2200mah traxxas iD battery, it works extremely well out of the box with the default configurations.
matt olmstead
Reviewed in Canada on December 31, 2023
Great unit for Latrax Tetan. Installed in 20 min, no extra parts needed. Running Zee 2s 2200 mah 50c
Tate Normandin
Reviewed in Canada on November 26, 2023
Product does not work. Stutters way too much be useful.
yoann
Reviewed in Canada on July 6, 2022
Perfect upgrade for latrax teton and prerunner! I can now run over 1h30 with a single 2200mah lipo and it performs really well! Only thing you should do is put a few tiny drop of glue arround the rear cap cause it might come loose at some times. Other than that its superb!!
Leplombier1987
Reviewed in Canada on June 26, 2022
First of all, the esc:pros:eletronic brakevariable speedcan handle 2s lipono need to solder anythingcons:not waterproofthe switch is big for no apparent reasonI bought this for my rc18mtx, it had a 370 motor before its the same size and the holes to fix it.it has a standard t batterie plug would be nice to fit an adaptater from t plug to female jst but that would be a bit more expensive. Before buying it be aware that cogging is a minor issue we will see with time but mine cog at extremely low speed and goes to about 30 kmh to 40 kmh.If your looking for a cheap brushless motor/esc combo then you found the right one one think i could say is buy a heat sink made for a 370 motor because after running it for about 30min of hard bashing it became really hot it wont affect performance but you will add longevity to the life of the motor.
Dan Downey
Reviewed in Canada on March 5, 2022
I put this in my Latrax Prerunner, pro's are it drops right in, cons are, it cogs, its not predictable, there seems to be a delay between the trigger pull and the truck actually putting power out, all in all if you want to go fast its okay, if you want a predictable truck that responds well to input this is NOT it
Michael longo
Reviewed in the United States on October 6, 2021
Installed on my son's LaTrax. And a issue with the first one, so swapped it out in a return (went very smooth and fast). Installed new one and ran good for the 3 times I got to run it. The input shaft on the motor broke and now I have to purchase a new setup.
Star C.
Reviewed in the United States on August 9, 2020
I bought this to replace the La Trax Teton motor and ESC. It was a very easy and fun task. I didn’t need to do any modifications. It fit perfectly. Later after I ran it on a 2s lipo, it thrashed the plastic stock gears. Lol. I kinda figured it was going to. I don’t know what speeds I’m getting but it’s fast! Really fast. Doesn’t get hot. The cheap ESC does a great job. I would absolutely buy this for smaller rc motors. Again and again. I’ll try to upload some photos later.
Paul R
Reviewed in the United States on August 22, 2020
I got this combo along with some 3s 1300mAh 30C packs to run my Losi Mini-T2.With all that and a new 23T pinion gear it runs great and is insanely fast and overpowered. I've had it out to some parking lots but still haven't had enough room to let it really go full throttle for more than a second or two.These 3s packs and 23T pinion are really too much for extended running and I'm always sure to check the motor temp and not run it too hard. I'm pretty sure backing back down to the stock 15T pinion would make it perfectly sustainable and it would still be real fast.
Matthew R Bailey
Reviewed in the United States on February 2, 2020
One of my main goals with this was to try 3S in my heavily modified Latrax Rally. No-go.....the ESC just blinks red when plugged into 3S. I have the programmer, tried various low-voltage cutoff settings (including 0 volts), two different batteries at various states of charge, tried plugging in the programmer while running off 3S. This is a big bummer for me, will probably just have to order a different ESC. Product description needs to be updated for sure.Noticed another oddity. Near full throttle, the RPM "jumps". That is, throttle response is relatively smooth and linear up until just about max throttle. There is a clear and obvious jump in RPM. Not a big deal for bashing a Latrax, but I could imagine this causing issues for racers.On the plus side, when paired with a 20t pinion, my little Rally hit 25mph (stock with the 2S is around 20mph). That's a respectable increase, and there's still tons of torque. It subjectively seems to have more torque on the 20t than the stock brushed has on the 14t (I used to notice the brushed motor bogging down when turning hard).If you're happy with 2S (which, really, is about all the Latrax cars can handle without some serious re-engineering), then this is probably a good choice. It did slide in with no mods required, and the stock motor bolts mounted right up.
J.K.
Reviewed in the United States on January 25, 2018
I put this in my Latrax Teton. I also bought the programming card and set it to the lowest take off speed.It works very well so far. The motor plate does need the bottom holes enlarged just a hair for smooth motor adjustment.I had already geared from the original Pinion/Spur 10T/60T to a 14T/54T.Using the original NiMH battery and those gears, it is very quick. It gets the tires off of the rims.ESC max temp was 106F, Motor 128F. I changed out the gears to 22/50, metal from Integy.It flys! I do however need to adjust the take off speed with that gear setup. It needs more torque to get going.I will get temps for the current setup later and post them. I also have bigger wheels, and a lipo on order.
J. Barry
Reviewed in the United States on March 6, 2017
Perfectly fits a Latrax Rally without modification, but you will need two different screws, I reused some M2 hex screws that I had laying around for my 1/16 Revo.It doesn't feel much faster than the stock motor, though this could be because it has a terrible time getting traction with stock tires, however it doesn't get too hot running 2S lipo batteries and I haven't broken anything with it yet, so A+!Pros:Direct fit for Latrax 1/18 scale carsGood powerHasn't broken stock components yetFits stock pinion gearDoesn't overheatLipo cutoff(not tested)Itty bitty tiny little ESCCons:Engrish instructionsStock motor screws aren't the correct size or thread pitch(Meh)Nothing anywhere on this says "GoolRC", it looks like a cheap generic set(well....it kind of is.)No programming card, and it doesn't seem like you can program it with anything but one.ESC looks cheesy as a block of cheddar that's sitting on a block of Swiss, seriously, it's a circuit board with a heat sink glued onto it, it does work though.ESC and motor wires are not insulated with SiliconOverall, it's cheap, it works, it does what I ask of it and it takes Lipo'sI had to seriously nitpick for the cons, the only one that truly bothers me is no built in programming method and nothing states what programming card it needs if I ever want to change something around.
Recommended Products
