Your cart is empty.
Your cart is empty.Product Description
Norm Mac
Reviewed in the United States on March 5, 2025
Standard snap on, pull off grease couplers are the only thing that makes greasing equipment a little difficult.The difficult part is finding the perfect tension around the zerk. Too loose and the grease leaks all around the zerk connection making a sloppy mess. Too tight and it takes a lot of pull force to pop the coupler off the zerk when finished.To make it work better I always end up putting the coupler on loose then tightening it, now I can grease cleanly then loosen the coupler in order to remove it. It's not difficult, it just adds a little to the process.These trigger couplings work so simple and great I can't believe I didn't switch sooner.Squeeze the handles, pop it on the zerk. Release the handle and it is tight to the zerk with no leaking. Squeeze the handle again and it releases from the zerk easily with no strength or pulling needed.This worked great for every grease fitting on my RV trailer suspension system. 18 different fittings and it worked great on all of them.If you have zerks in tight or hard to reach areas this coupler may be too large to fit so check your equipment first to make sure it will work for your needs.
Josh
Reviewed in the United States on March 28, 2025
Great piece to have in your grease gun kit
Hippy Bryan
Reviewed in the United States on March 28, 2025
This 90 degree is great for some hard to reach fittings. My upper balljoints have always stymied me with their minimal clearance around them, but this tool can squeeze in there and actually get grease into the joint. I also have a couple of u-joints which have given me trouble before which this adapter can slip onto and not just spray grease around the zerk.Ease of install and removal will depend on the exact zerk you're targeting. Too wide of a zerk neck and you might need to file down the slot a little, but it's easier to take material off than add it, so I'm glad they made it a tight fit. This adapter is somewhat difficult to apply, so I only use it when it's the only option. It's easy to remove from my grease gun and put back in the toolbox since it snaps in-line.I have other 90 degree grease fitting couplers, but none which can fit in as tight of spaces as this one, so it's a great addition to my toolbox.
Pam
Reviewed in the United States on March 26, 2025
BEAUFORT BEAU-5047 Grease Gun Coupler - 90 Degree Grease Coupler Snaps on to Grease Fittings in Tight Spaces - Grease Joint Fittings - Push on 90 Degree Grease Adapter. This arrived quickly after ordering. It was here within 3 days. It is exactly as shown in the listing photos. It works well and is good for getting into those tight spots that they seem to love to put grease zerts into. It fit on my grease gun hose perfectly. There was no leakage and it was easy to install. It was also easy to remove once it performed the job that is intended for. It seems to be well built and should last for a long time.
Rick
Reviewed in the United States on February 24, 2025
Ordered this 90 Degree Grease Gun Coupler Adapter - Push On Design - 1/8" NPT Adapter for use in my shop.I have a farm tractor, two garden tractor mowers, and two trenching machines that digs water lines, electric & etc..I'm always servicing one of them, and have a few fittings (especially on trenching machines) that are very difficult, almost impossible to grease just because the tight & small accessible areas to reach them. I've tried multiple grease guns and styles and same story. Recently while shopping online for some oil filters and plugs, I saw this Beau - 90 degree push-on grease coupler, and started reading of how it works. After reading about it and understanding how it works, I ordered it. This was a game changer for me and this nice coupler was what I needed "years ago".This coupler is made of good hard allow steel, and rust resistant. It fit right onto my flex grease gun hose in a matter of minutes, not hours. I tried it on the toughest ones on the trenchers, on the drive shaft universal joints and it pushed/slid right on to the grease fittings just like it was made for them. I'm still impressed. All the worries I've had just trying to grease these for years. I like the way it locks/fits on the grease fitting as it doesn't leak at all, or hadn't yet. I kept on greasing until I had all my machines greased. The nice 90 degree design lets it slide right upon a fitting and lock in place and does it so easy for me. This easily earns a (5) star rating in my opinion
MNDave
Reviewed in the United States on April 7, 2025
One of the worst times you can have while working on vehicles is laying under the frame, trying to hold the grease fitting on a zirc while you pump the grease gun with your other hand and whatever you can find to lean it up against. This handy item threads on in place of the stock fitting on your grease gun and when you push in the handles, opens up the clamps inside the end of the nozzle, then you place it over the zirc, release the handles, and it should stay in place while you have two hands to run the grease gun. You still have to be careful not to pull on the hose too hard or it may come loose, but I find this to be a real mental health saver.
twofouroh
Reviewed in the United States on April 2, 2025
So I thought this would screw onto the end of the hose on my grease gun since they called it a coupler. Turns out it is an adapter, it has a grease zerk that you snap your grease gun coupler on to, and then you have 2 connections to spit grease and pop apart instead of one . . . Not an improvement, it should just screw onto the hose.P.S. - If they showed pictures of it from more than one angle, people could figure this out without having to order and return it.
A. H. Cosgrove
Reviewed in the United States on April 13, 2025
Perfect. Works exactly as advertised. Well made, and sturdy. Provides a good lock on the zerk and easy to remove. Good value and easy to install.
Recommended Products