Your cart is empty.
Your cart is empty.Upgrade your 2016-2020 Toyota Tacoma with these GS Power engine hood hinge ditch brackets, designed to securely hold your auxiliary off-road LED pod work lights. These brackets are specifically engineered to fit between the hood and cowl panel at the windshield base, providing a sturdy and reliable mounting solution. The package includes a pair of brackets, one for the driver side and one for the passenger side, ensuring compatibility with your vehicle. The installation process is straightforward and does not require drilling, only a wrench or socket is needed for a quick and easy setup. These brackets are not only limited to LED pod mounting, they can also be used for CB antennas or whip flags. Made of durable aluminum and powder-coated for a sleek finish, these brackets are a reliable and long-lasting addition to your Toyota Tacoma.
Ty A.
Reviewed in the United States on August 31, 2024
Not the thickest material, but gets the job done. Make sure you you space it so it uses the most outer parts of the slots so you won't have to redo it more than once!
Richard Bauer
Reviewed in the United States on June 12, 2024
Worked a treat and bolted right up to my Lexus GX470. Sweet deal for the price. I don’t think the finish will last years, but for the price it’s almost worth replacing every 3+ years.
Chuck Seely
Reviewed in the United States on March 11, 2024
Easy to install. No mods. Only tool needed is 12mm socket. THESE GO BETWEEN BOLTS AND HINGE! Not between hood and hinge. If you install that way the hood will sit proud and latch awkwardly.To install, remove bolt closest to front bumper, attach mount with other hole offset, replace/tighten that bolt, remove rear bolt, swing mount over into place, replace bolt and tighten. Doing it this way keeps the hood from shifting around so you don’t have to readjust it in relation to latch. SEE PICS
Angel
Reviewed in the United States on October 22, 2024
Perfect fit on a Toyota Rav4 Gen 5. Sturdy and good construction.
Ethan
Reviewed in the United States on September 10, 2023
Better than expected considering price, paint like other reviews is pretty thin but if yours careful putting them on its no big deal.How to install these since directions werent included:Get a couple blocks of 2x4s to wedge in between the hood and the windshield to try and limit moving (dont go crazy just make sure the 2 blocks are snug up between the windshield and hood on whatever side you are going to start with. Then remove both bolts on one side of the hood whichever side you put the blocks on to limit movement, I placed mine with the end of the mounts pointing out away from the truck. But you can point them facing in if you desire. Next put the bolts through mount and into their respective holes on the hood and tighten them down, I did this until they felt as snug as they were when I took them off, probably around 30 lb ft. Then move your blocks to the other side and repeat.I installed 3 inch cube lights they were about 4 inches long and 3x3 inches in height and width and have no problem with clearance from the windshield.
Andre Madore
Reviewed in the United States on March 21, 2023
I installed these on a 2019 Tacoma.The good: these brackets are super sturdy and the way they mount to the hood hinges is super easy to install. Absolutely no wobbling and they leave plenty of clearance for the window.The bad: the paint on these chips easily. I can take my fingernail to it and it chips. I'm going to wire brush them down and repaint them. Lastly, the fitment wasn't great. The driver side fit perfectly, but the passenger side hit out on the plastic fascia (where the wipers rest) when you close the hood, but just slightly. So I had to trim a sliver off the end to make it fit. All in all, not too bad.
ERIC BUEHNER
Reviewed in the United States on February 26, 2023
Installed on 1st Gen Tundra. Fit well with good clearance at windshield.Hood does sit high but could be lessened by filing the bolt holes or relieving the wiper cowling, I did neither.Installation is easy, just remove lower hinge bolt, install bracket, install and snug bolt, remove upper bolt, rotate bracket to align with hole, install bolt, tighten both. Repeat on second hinge. Took me less than 10 minutes.Product seems beefy with good finish and paint.
Jason White
Reviewed in Canada on February 16, 2022
We’ll made, metal painted well
Dandelion
Reviewed in Canada on February 9, 2021
I installed one bracket in 2 minutes. I went to install the other, and realized the holes don't line up.... by about 50% of the bolt width..... It was clearly fabricated incorrectly. I grabbed a file and spent 40 minutes filing the holes to be able to bolt it on. Overall, for under 30$, this was still the cheapest option. I would rather file it down than buy one for over 50$... A new pair of ditch lights costs that much!
brandonb927
Reviewed in Canada on February 17, 2021
These hood brackets for ditch lights are great quality! The powder coating is solid and the holes for the brackets lined up correctly.
TW
Reviewed in Canada on February 10, 2021
Fits 2010 Tacoma. Easy install and great product for the price. I read some comments about thin powder coating but I had no issues with these. Very happy with the results. Would buy again.
Spencer Norris
Reviewed in the United States on April 7, 2021
Bought for my 2017 Tacoma knowing it wasnt specified to fit, on the upside it will fit as it comes, but with a little know how it will fit perfectly.Overall decent design, bends are nice, powder coat is nice, NOT great, but definitely not the worst I've seen from an Amazon product. However there are a few areas that are applied chunky or have some marred edges.Thickness is also fair and not flimsy.All in all, you could get MUCH worse for your money.Would recommend.
Grimel
Reviewed in Canada on May 7, 2020
Utiliser dès rondelle en caoutchouc pour fixer le boîtier du led !!!!
Recommended Products
