Your cart is empty.
Your cart is empty.
Attributes:
- High Quality and Light Weight Frame Sliders (Left & Right Sides)
- Frame sliders help to protect the frame, engine cases and bodywork/fairings to minimize the cost of repair
- Professional installation is recommended
Specifics
- This frame slider is EXTENDED. This is 1" longer than the original
- Quantity: 1 pair
- Instructions: Not Included
- Condition: Brand New, Never Used
- Color: Same as picture show
- Material: Delrin
Quick bullet points about sliders:
- They are not designed to protect plastics, clipons, or rearsets, even though they might help sometimes.
- You do not want a slider to stick out too far or it will help flip your bike in a crash by snagging on the ground, curb or anything else.
- You want delrin or plastic to touch down when you crash as they will grind off and not catch on anything and if hit hard enough or direct enough they will shatter.
- If your slider shatters, grinds off or bends then it did it's job. You don't want it solid after a crash or it didn't absorb any energy but merely transfered it on to what you bolted it to.
- When f1 cars hit the side of a track they explode as they don't want the drive to absorb the energy. Frame sliders are the same way. You want them to stay attached but get beat up and take the energy.
- If the bolt on a frame slider bends that's a good thing as the only other option is to put the energy on the frame or mounting point. Better the bolt bends. Also if it didn't bend it might have flip the bike by snagging something. A mangled frame slider, but still on the bike, did it's job.
- No cut frame sliders aren't a direct bolt on like cut sliders as they often have a bracket.
Fitment:
- 2004-2012 FZ-6 , FZ-6S , 600
Daniel Roizen
Reviewed in the United States on December 8, 2024
These bolts appear like they will fit my wife's Yamaha R3. However, there is no grade on the engine bolts. Big yikes, probably some Chinesium. Returning as I took the risk with Chinese footpegs and they snapped. Not again!
Roberto Carlos Jimenez Villalobos
Reviewed in Mexico on September 29, 2023
Buen producto, solo que los tornillos no le quedaron a la Yamaha MT03, tuve que comprar de 1" mas largo
Kud
Reviewed in the United States on August 21, 2023
i know this is not it's intended use, but many have reccomended it for this, i looped the bike today and this is the aftermath.
Jay
Reviewed in the United States on March 19, 2023
I ordered 3 different sets before I got these they were all cheap plastic and ugly finish work. These are the quality durlin look and feel you really want. Highly recommend
That guy
Reviewed in the United States on December 5, 2023
They work great and were super easy to install. I used them on my Yamaha bolt.
Joseph Parra
Reviewed in the United States on October 8, 2023
Very easy to install, they weren’t exactly what I needed for my Grom clone. But with some small modifications I got them to work as rearset savers ! The delrin looks and feels good
RA Deleon
Reviewed in the United States on November 30, 2022
I got these because everyone was reselling these as Grom Rearset savers for $80 or more. I have a Grom SF and the delrin sliders fit right in but the bolts dont fit because theyre too big. You need to buy (SF I can confirm only) bolt size M8 x 1.25mm x 90mm or 80mm and this will work fine. It comes with 1 washer but you can add a few if needed to make a snug fit. Your welcome!
Jonathan E.
Reviewed in the United States on April 20, 2022
Worked on the lower bolt of the rearset as a slider that does not let the peg break from ground and pound. Your welcome ya filthy animals!
Sergey Kiritchenko
Reviewed in the United States on August 21, 2018
The bolts provided were absolute garbage. They were not going in smoothly at all compared to the original engine mount bolts. That’s not even the worst part, while trying to loosen the bolt out, it began to get stuck and snapped off inside my engine mount. Questioning the grade of these bolts..
Recommended Products
