Your cart is empty.
Your cart is empty.Product Description
Ingersoll Rand model 9512 Quick Change Retainer for . 401 Shank Chisels. Fits Ingersoll Rand pneumatic hammer models: 121, 132 and 772. This quick change hammer coupler holds 0.401 shank chisels in place, simply install the chisel by pulling back the collar.
From the Manufacturer
The Ingersoll Rand 9512 Quick Change Retainer will fit on almost all maintenance air hammers - ours as well as our competitors.
disappointed
Reviewed in Canada on March 19, 2025
Broke within a month.My son sent it back to the company under their ““lifetime warranty” but since we are in Canada, we had to pay the shipping to the US and then once the new product came back, we were slapped with an additional fee from FedEx. The total cost to send the product back with the additional fee from their shipping company cost almost more than the actual item. So if you live in Canada and want to purchase anything from Capri tools, you better think twice.They said that the rules were written in their warranty information posted online, but it had nothing to do with warranty on an item it’s strictly for orders.There is nothing to say that you’re responsible for shipping back one of their defective or broken items to be covered under their warranty.
Carlos
Reviewed in the United States on June 27, 2024
Ayuda al cambio rápido de los buterolas o pines de remache
dick
Reviewed in the United States on April 12, 2024
I was covetous of this quick change since I first saw it on an IR air hammer. Jumped at the chance to have the same convenience with my own air hammer at a reasonable cost without the waste of tossing my existing gun. No problem installing and using on my gun.
toad
Reviewed in the United States on September 7, 2023
I had to return this. It would not fit on my Florida pneumatic air hammer. Not the fault of IR.
Customer
Reviewed in the United States on March 11, 2023
Works Flawlessly
A Team Fabrication
Reviewed in Canada on November 1, 2022
Would buy again
Ted
Reviewed in the United States on July 31, 2021
I've had an IR pneumatic hammer for years and it has worked great. Then recently the retainer (coil spring) broke off. I was using the tool to hammer through a concrete block wall. Without the retainer when I broke through the wall the chisel would shoot across the room on the other side. ( a little unhandy) I hunted the internet and local suppliers but no luck. IR said "no longer available" and reviews from other sites said their retainers wouldn't fit my tool (mod #121). Then found this one. I had used this type before on another hammer and it was a great improvement over the coil spring type. Made by Ingersoll Rand, and very sturdy - good quality and it fit perfectly. Glad I didn't have to throw the baby out with the bath water. Now I have a better tool that I did before the retainer broke.
Customer
Reviewed in Canada on June 11, 2019
Fit well
Kindle Customer
Reviewed in Canada on August 5, 2018
Holds the chisel great and secure. Installs in about two minutes. Real decent quality like you’d expect from IR. Spend the extra few bucks it worth it.
Customer
Reviewed in Canada on March 6, 2018
Great product. I installed on Mastercraft Maximum air hammer. I am truck and trailer mechanic. I put my tools thru hell. This thing is standing up to the abuse.
SS
Reviewed in the United States on March 5, 2014
Ingersoll Rand 9512 Air Hammer Quick Change Retainer, Silver. Much better than the silly spring that the air chisel comes with, almost completly eliminates shooting chisels across the room, much safer and a lot easier to swap chisels. I have had one of these on the other air chisel for about 20 years, I had a cheaper one but it broke after about 1 year. Unfortunatly this one has the plastic spacer like the cheaper one that broke had, time will till if it lasts.
JMS
Reviewed in the United States on July 5, 2012
It's a wonderful idea, and is easy to use...UNTIL you use a particular bit for an hour or two.Then what happens, is the part of the bit that is held by the retainer starts getting a little wear ring around it, just like a standard chisel would.It only takes like 1/32nd of an inch of that ring to prevent you from being able to remove the bit.If you have snap-ring pliers, that's not a terribly difficult thing to disassemble, but it only happens when you're not expecting it. :-)If it were more forgiving about that little bit of wear, it would be perfect.Right now, I just examine the bit periodically, and grind it down before it gets too bad to pull out.
Scott W
Reviewed in the United States on July 13, 2012
Easy to install and makes changing chisels WAY easier.I installed on a IR model 121 hammer. Takes about a minute to install: Just unscrew your existing spring, screw on this retainer, and tighten the three set screws.The retainer uses a ball-lock system to retain the chisel. Pushing down the spring-loaded collar retracts the balls and allows chisels to be freely inserted/removed. When released, the collar springs back into position, exposing the balls and holding the chisel in place. With this installed, changing chisels becomes a 1-second operation.At under twenty bucks, this should be standard equipment on every IR air hammer!
Recommended Products
$132.76
$ 58 .99 $58.99