Your cart is empty.
Your cart is empty.Jayvon
Reviewed in the United States on July 24, 2024
It fit on good, you have to stretch it or when you try to put it in, and squash your lens together, a lot of extra butyl will spill out (which is good, since it’s a sign of a good seal). People who say they have a leak either didn’t clean out the fitting correctly from the old butyl or overstretched it and made it too thin. I was able to seal my headlights twice with the single roll, I still have a bit of butyl to do one headlights but let’s say if you stretched it, you could possible do 3 sets of headlights.
Kyle
Reviewed in the United States on May 14, 2024
The butyl worked great and sealed my headlight up just like oem. No moisture or issues!
Maurits W.
Reviewed in the United States on October 12, 2024
I resealed my 2006 Subaru Forester's leaking headlamp unit successfully with this sealant.
Flow558
Reviewed in the United States on April 17, 2024
Once you get it going you can not stop .
Pang
Reviewed in the United States on December 22, 2023
This butyl rubber appears to have a slightly higher temp profile than others. When you go reheat it to do your final press and seal, this stuff is very sticky for sure. It gets soft as intended, but stays together. Other butyl rubber that I've used in the past, becomes sticky but also really messy. This stuff is sticky but not as messy if that makes any sense. You can hear any air pockets come out of the channel, as your squeeze together the lense together, so you know you have a good seal. Clean up is very easy with some alcohol.
Guenter Thumser
Reviewed in the United States on December 2, 2023
Butyl sealant works great for replacing headlight lens. The tricky work is to get the old lens removed. Once this is done, the new sealant is easy to use.
Customer
Reviewed in the United States on November 8, 2023
Used this to re-seal the headlights on my Lexus LS460 after retrofitting clear lenses and upgraded high beam projectors. This was the first time I'd ever opened a pair of headlights so I don't have experience with any other butyl glue products to compare this to. That said I found this product effective and easy to use - I found that if you throw the box in the oven for a bit it's that much easier to work with.
عادل بن منصور
Reviewed in the United Arab Emirates on April 22, 2023
ممتاز وسهل الاستخدام لمصابيح المركبه حيث انني قمت بفتح وتغيير زجاج المصابيح والجميل انني استخدمته بدون قفاز فهو متماسك
Hass AL
Reviewed in the United Arab Emirates on March 5, 2021
This is an amazing product and it is mu h better than other brands around in the market
Ray
Reviewed in Australia on September 5, 2020
All good A+++++
Andrew
Reviewed in the United States on June 15, 2020
Hands down the best stuff for your retrofit project. Throw it in the oven for about 3 minutes at 150-200 degrees to make it a little more workable when trying to get it into the channels on your housing. Reheat everything again for another 3-5 minutes and use a flathead or screendoor roller to push it into the channel flush and evenly. I will add if you reheat this stuff again to redo a retrofit or take apart your housing again for whatever reason it gets extremely stringy, more so than most oem butyls, so be mindful of this so none of it sticks to the lens or any of your headlight internals or you could have a small disaster cleaning that off! Other than that it’s great and one roll has lasted me two retrofits with full sized headlights (Genesis Coupe) and two fog lights (also Genesis Coupe) and I still have a lot left!
Davo
Reviewed in Australia on December 26, 2020
Good product, inexpensive, saving big dollars on repairs.
Marcopolo96
Reviewed in Canada on August 25, 2019
Good product. It is expensive but well worth it to restore my headlights and stop fogging. After 2 weeks it has held up against the elements. Hoping it will last for years to come.
Recommended Products
