Your cart is empty.
Your cart is empty. Part Number:
Rocker Arm:3L3E6529DA, 3L3Z6564A, 3L3Z6564BA
Valve Lifter Kit:5L1Z6500A, 5L1Z6500AA, 5L1Z6C501AA
Part Name: 3L3Z-6564-BA Rocker Arms & Lifters Set
Applicable Models:
(The Compatibility Is Just For Reference. Please Compare it With Your Original One Before Purchasing! )
F-ord Expedition 2005-2014 5.4L V8 Cyl
F-ord Explorer 2006-2010 4.6L V8 Cyl
F-ord Explorer Sport Trac 2007-2010 4.6L V8 Cyl
F-ord F150 4.6L(2009-2010) V8 Cyl & 5.4L(2006-2010) V8 Cyl
F-ord F250 Super Duty 2005-2010 5.4L V8 Cyl & 6.8L V10 Cyl
F-ord F350 Super Duty 2005-2010 5.4L V8 Cyl & 6.8L V10 Cyl
F-ord F450 Super Duty & F-550 Super Duty 2005-2015 6.8L V10 Cyl
F-ord F53 2000-2004 & 2006-2009 & 2011-2015 6.8L V10 Cyl
F-ord F59 2011-2015 6.8L V10 Cyl
F-ord Lobo 2005-2010 5.4L V8 Cyl
F-ord Mustang 2005-2010 4.6L V8 Cyl
Lincoln Mark LT 2006-2008 5.4L V8 Cyl
Lincoln Navigator 2005-2014 5.4L V8 Cyl
M-ercury Mountaineer 2006-2010 4.6L V8 Cyl
Package Include:
24PCS Engine Rocker Arms+24PCS Valve Lifters As Pictures Shows
Kindle Customer
Reviewed in the United States on February 27, 2025
Should be a 0 star. Do now buy this junk the lifters are to long and after you install them your valves don’t close all the way so you will end up doing a complete tear down to replace them again. I seen they where slightly longer then the old ones, but have over 200,000 miles on my truck so thought the original ones are just worn. But nope the new ones are not right.
Robert McNaughtan
Reviewed in Canada on August 25, 2024
These parts looked like they were going to be perfect. I soaked the valve lifters in oil overnight and following day I installed all new parts. upon attempting to start engine, I noticed zero compression from every cylinder. AT THIS POINT, I reinstalled the old push rods and found that I now have compression. At this point, I compressed the new push rods in a bench vise carefully to drain oil from each lifter assy. The push rods in each lifter could now be pushed down and allowed to move back to top of unit. I reinstalled the new push rods and the engine now runs very rough. Do you people have any ideas as to what I can do? Do these push rods have to be replaced and if so will they be covered by warranty Please let me know ASAP as this job has involved me for several weeks. THANK YOU FOR YOUR HELP AND ADVISE.BOB. My concern is that these parts do not work. Are you people going to send me new ones, or are you going to just refund me full amount for complete package ? Please reply ASAP as I need to get this vehicle completed ASAP. Thank you. BOB
Marshall Wayne
Reviewed in the United States on May 21, 2024
They were just what I expected. I don't recall if they were large or small hole for the oil passage but I've had no issues with them. Tightened valve train up and the truck sounds and runs better. I wouldn't do a timing job without changing these.
Recommended Products
