Your cart is empty.
Your cart is empty. Water-proof in-line Fuse Holder provided by MUYI Features excellent water-proof design with tight-fitting rubber cap, 14 AWG thick copper wire. Fit for mini blade fuse. 30cm/12inches pigtail wire loop allow you to cut and splice it into any project.
MUYI high quality fuse holder and correct fuse can protects a circuit from overloading in extreme operating conditions or in the event of a short circuit, keep your car and electric device in safe condition.
Specification:
Material:copper(coated with tin), rubber
Condition:100% New
Color:Black with red wire
Operating Temperature: 30℃~170℃
Fuse holder dimension:approx 38x25x13mm
Wire Length:approx 30cm/12inches
Wire Range:14 AWG
Amp Range of Fuse Holder: 1 to 20A
Fuse Holder Voltage Max Operating:32V DC
For Fuse Series:Mini Blade Fuse(ATM)
Fuse included: Yes
Feature: Cover. Excellent water-proof design.
Each Set include 1x fuse holder and 1x 15A mini blade fuse.
Package Included: (6 Set)
2 x Mini Blade Fuse Holders
6 x 15A Mini Blade Fuses
ATTENTION:
1，Fuse holders are designed with 14 AWG wire and they can support fuses rating 2A, 3A, 5A, 7.5A, 10A, 15A, 20A.
2，It is important to select the correct Amp rating before you install or replace fuses even though they come with commonly 6 x 15A fuses.
3，Fuse holders are safe for use below Voltage Max Operating: 32V DC
Patrick F
Reviewed in the United States on August 22, 2024
Need fuse holders for add on wiring using the tiny chip style fuse, had to have to replace stock
Samantha
Reviewed in the United States on December 30, 2024
These fuse holders are as good as any of the "big name" ones I have used for much less money. They do everything I need them to do.
Aaron D.
Reviewed in the United States on November 21, 2023
They look good and work as described. The wire fits perfect in the correct crimp connector. (Blue)
mustwatchtv
Reviewed in the United States on May 14, 2021
Very happy with this product, I used it on my bilge pump for my boat. Installation was easy and the perfect gauge wire.
Robert J.
Reviewed in the United States on February 17, 2020
These did the job I needed them to do. I cannot speak to the weather roof or waterproof properties of this item, because mine are mounted in my trunk, but the seal slips over the fuse nice and snug. The fuse is also held into the body of this very snug, so contact is great. Wire gauge is beefier than most, which is why I chose this one in particular. Doing well for me!
Hogn99
Reviewed in the United States on October 15, 2020
I like these. I bought two packs to run with wire harnesses for ATVs. I like the minis so these work well. So far I have run one with the supplied 5A fuse, and one with a 10A fuse due to the load. I haven't tested, but I doubt water will get in. They should not get submerged where I installed them, but the splashing should not affect them. Opening and closing was not a big deal, as some reviews said. My issue was how tight the fuses fit; putting the first one in was tough, to the point I bent the fuse a little. Take your time and work them in slowly. After that I was able to pull and install much easier. Will buy again.
William F. Swanson
Reviewed in the United States on September 2, 2019
Used these to re-wire some switches in the stern of my 2004 Sailfish 236cc. Worked great, nice seal on the fuse too.
Aidan
Reviewed in the United States on October 23, 2019
Bought this for my '86 Honda TRX200SX project. The original fuse holder was completely busted, it was one of those bulky glass tube style fuses, at 15 amp rating. Bought this pack of two, comes with two fuse holders and two good quality 15 amp mini fuses. Wired it in place of the original fuse holder and everything works as expected. The holder is built well enough and closes tightly around the fuse to keep the elements out, the wires are firmly attached and sealed in place, a good tug would not pull these things apart. Everything is as expected for a great price, if you need a good deal for 15 amp fuses with holders for your automotive project these are the ones to get. Fuse holders have about half a foot of total wire, you cut the wire somewhere in the middle and install as needed. Perfect. Will update if any problems occur, do make sure you fully close the fuse holders once the fuse is installed to insure a good seal.
Recommended Products
