Your cart is empty.
Your cart is empty.Product Description
Product Overview - PADLXSM (910058)
The Primary Arms Deluxe Scope Mount is ideal for 1913 Picatinny and similar “flat-top” mounting platforms. Aluminum construction, durable matte black anodized finish. 2.52 inches of clearance between the rings. Places the center of your 30mm tube scope 1.5 inches above the rail. Fits scopes with 30mm tubes.
To make sure the mounting nut is fully tightened, turn the nut clockwise until resistance is encountered. After that, turn another 1/2 turn. If a torque wrench is being used, we recommend no more than 35-40 in-lbs.
EXPORT CONTROLLED ITEMS: These items are controlled for export and may require an export license from the U.S. Government. Buyer acknowledges that Buyer is responsible for obtaining all export licensing authorizations and filing all export documents prior to export from the United States.
David M.
Reviewed in the United States on June 18, 2023
This thing is just as good as mounts costing 3-4 times what this sells for. Sturdy, looks good and the holes tested concentric. I always lap rings and these needed it. I'm very happy with this mount!
Frank
Reviewed in the United States on May 17, 2023
Does exactly what it says. Read the instructions and you'll have a good time. I was overly cautious and didn't tighten the rail portion enough. Hand tighten, use a wrench, take it to snug then turn it a quarter turn past snug. That's worked for me so far. For the optic, do the same, preferably use a torque driver or torque wrench. A quarter turn past snug seems to be holding and not damaging the tube. You do not want to over tighten the on the tube, it will ruin the optic and self induced damage is not covered under warranty.
RHINOMAN JF
Reviewed in the United States on December 31, 2023
These mounts are fantastic. I ordered mine but was refunded because it never arrived. Then I reordered Is it through a different source.. they were very nice with customer service and the mount is fantastic.
Eric
Reviewed in the United States on December 23, 2023
This mountain was cheap wasn't sure how sturdy it was going to be I bought it to go on my primary arms one by six lpvo. It was simple to install and so far it has held zero through approximately 600 rounds out of my AR-15.
jdfletch
Reviewed in the United States on January 28, 2020
I have purchased several of these mounts from Primary Arms in 30mm and 1”, Both extended and regular. They have all been of high quality and fit well. Removing and remounting the scope mounts results in no perceived point of impact shift. These are my “go to” mounts for the AR platform. Perfect for putting the scope at the right height and forward position for an A4 upper.
Customer
Reviewed in Canada on September 15, 2019
Complete junk! I tried 3 different scopes with it and none would hold zero. Even at 50 yards the best group I could get was 2 and 1/2 to 3 in. Save your money and buy something that's actually good quality.
Gerry
Reviewed in Canada on May 9, 2019
Not exactly what I thought it would be for what I was looking for
Emily
Reviewed in Canada on May 23, 2019
Fits perfect, feels solid.
Bugsbunny45
Reviewed in the United States on March 26, 2019
I bought this through Amazon but it was sent by Primary Arms. I am glad I saved money on this. I am using it on my vortex viper pa 6.5 - 25 50 mm. Its a solid mount. Why spend extra this does the job plus and is reasonable priced.
JimR
Reviewed in the United States on March 28, 2017
Very nicely made! I was surprised by the accuracy of the machining and finish. I did not have to lap the rings to fit the optic (Primary Arms 1-6X24mm ACSS). A bargain for $60.00! It's not a LaRue Tactical mount, nor an American Defense mount, but it works very well! Time will tell on it's durability and its ability to retain zero. I, however, do not think I will have any issues. If you need a mount that you will use on one rifle, and leave on that rifle, this may well work for you!
David Greene
Reviewed in the United States on February 14, 2016
It's an ok mount. Not as well made as I would like, but the price was right and it's machined pretty well. With lower cost you lose a couple things, it's heavy, and the threading isn't the best, and the nuts are obviously the weak point. USE A TORQUE WRENCH.
Recommended Products
$10.98
$ 4 .99 $4.99