Shopping Cart

Your cart is empty.

Your cart is empty.

Push to Connect Fitting 3/16' Tube OD x 1/8' Male NPT Thread, Pneumatic Male Straight Air Water Line Quick Push in Connectors (Pack of 5)

Free shipping on orders over $29.99

$11.98

$ 4 .99 $4.99

In Stock

1.Size:1/2 Mnpt - 1/2 Od


About this item

  • Quick installation, simple and flexible, space-saving. Even after installation, the direction of tubing can be changed freely.
  • The release ring adopts the ellipse design to make it more convenient and labor-saving for disconnection. Stainless steel locking claw, never stuck, never rust.
  • All taper threads are pre-coated with Teflon with fine seal performance. (It may needs extra Teflon tape when thread of equipment damaged before.)
  • Fit for icemaker, refrigerator, cold water filter, etc. Please do not apply for the tube joint with additional external load (bending, twist or pulling, e.g.: Trailer, Air Suspension).
  • Pressure Range: 0~1.1Mpa(0-160psi), Negative Pressure: -100Kpa (-29.5 in.Hg), Pressure Proof Test: 3.0Mpa (435psi), Temperature Range: 0~60℃ (32~140℉), Applicable Tube: Nylon,Polyamide (PA) / Polyurethane (PU). Applicable Fluid: Air, Vacuum, Water.



Before use, it should make clear following points
Warning

a) Except air and water (only special type and custom-design, e.g.: icemaker, refrigerator, cold water filter), never attempt to use the tube joint other fluids.
b) The tube joint application is prohibited where spark and fire might be occurred.
c) The tube joint application is prohibited if water temperature is above 60℃ (140℉) because resin might be decomposed and damaged in water under a high temperature.
d) The tube joint is not designed for application where there is static charge.
e) Never apply tube joint with additional external load (bending, twist or pulling, e.g.: Trailer, Air Suspension),
Cautions
1) If you use other supplier tubing, the different tubing tolerance might case leakage or incorrect connection and disassembly. It must check if tubing OD is measured by Metric Size or Inch Size.
2) Always check the end of tubing for a right angle cutting and check the external surface of tubing for any damage or scratch. Please refer to following instruction in connection of tubing. When you insert the air tubing into the joint, you will have two-step feeling. Section One is locking claw while Section Two is sealing ring. You must insert the tube into Section Two.
Sleeve is used in tubing connection and disconnection. The sleeve is designed as an oval shape, which is convenient in assembly and disassembly. After connection of tube joint and tubing, always try to pull tubing and ensure its firm connection.
3) Cautions during disassembly of tubing before disconnection of tubing, always check tubing internal pressure for zero.
For disconnection of tubing, always press sleeve heavily and then pull out tubing. If sleeve is net pressed with enough force, it is hard to pull out tubing and external surface scratch might be resulted by locking claw, which is the cause of air leakage.


Kaos
Reviewed in the United States on January 6, 2025
These feel very solid. They don't finger tighten very far but easily tighten securely with a wrench. The 1/8 inch tube connection is very secure. Tested for leaks after installation, none found.It took me some digging to find these; I wanted a simple adapter for my V2 CarbonDoser to the V1 CarbonDoser's regulator but this particular size combo was tough to track down. I'm very glad I found these and that they were so easy to use with no problems.
Customer
Reviewed in the United States on March 24, 2024
worked great
Jack English
Reviewed in the United States on July 31, 2023
Will not reseal after removing hose one or twice.
SAM
Reviewed in the United States on June 1, 2023
all 5 failed to make a full seal on the push in connection. Same tubing created a leakfree connection at all other fittings in system.edit: replaced with different brand fitting with the same specs, new fitting works perfectly, these fittings are definitely out of spec.
Kent S.
Reviewed in the United States on May 4, 2023
Perfect, exactly what I needed and great quality
Emiel De Weerdt
Reviewed in the United States on December 16, 2023
good quality
City of Norfolk
Reviewed in the United States on October 18, 2023
Fast shipping! good quality!
Keith C Norris
Reviewed in the United States on October 11, 2023
The top quick connect fitting that attaches the clear filament guide line to the print head on my Flashforge Adventurer 3 3D printer broke. The fitting would not hold the plastic line in place. Each time that you would go to print, the line would dislodge itself. From reading several printer forums, this is a fairly common occurrence on this 3D printer.This part easily installs with a slender head 10mm open-end wrench. Once the new connector is installed in the print head, I would recommend trimming off 1/8" of the clear plastic tube. Make sure when you trim it to cut 90° perpendicular to the line so it fits squarely in this quick connect fitting.Saved me a lot of time, and my kids are happily printing again!