Shopping Cart

Your cart is empty.

Your cart is empty.

Replacement Part SRV7000-660-AMP for Pelpro Pellet Stove Igniter & Pleasant Hearth Pellet Stoves Ignitor, 300W…

4.8 (9) Write Review
Free shipping on orders over $29.99

$13.49

$ 5 .99 $5.99

In Stock
  • Compatible with PelPro Pellet Stoves and Inserts: PP130, PP60, PP60-B, PP70, PPC90 Cast Iron, TSC90 Cast Iron, PP130-B and Replacement for Pleasant Hearth Models: PH35PS, PH50PS, PH50CABPS
  • 300 W, 110/120 V AC.Furnace Replacement Heating Elements. Measure from hub 4 3/16'', Total length of element 4 7/8'', 16'' Lead Wires
  • Replacement For Part Number: SRV7000-660. Igniter Furnace Replacement Heating Elements cable for PelPro and works with Pleasant Hearth.
  • HIGH QUALITY REPLACEMENT PARTS - It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to pellet stove igniter failure.
  • Service: 1 year protection from the date of purchase. If it fails on your stove, please do not hesitate to contact us via Amazon Message or email.


Product Description

KEEP WARM IN WINTER WITH FAMILY AND PETS!

stay warm in winter with family and pet

Genuine original replacement igniter for compatible with PelPro pellet stoves.

Compatible with PelPro Medel:

  • PP130
  • PP130-B
  • PP60
  • PP60-B
  • PP70
  • PPC90 Cast Iron
  • TSC90 Cast Iron

Compatible with Pleasant Hearth Medel:

  • PH35PS
  • PH50CABPS
  • PH50PS

Replacement For Part Number : SRV7000-660

It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

easy to install stove igniter tube in cold weather at Country house

EASY TO INSTALL

1. Turn the dial control to the off position. Unplug the power to the unit.

2. Unplug the wire leads to the igniter.

3. Remove the screw in the side of the igniter chamber. Pinch the ends of the bracket together and pull the igniter straight out of the igniter chamber.

4. If there is difficulty in removing the igniter from the chamber, the chamber can be removed from the rear of the firebox by removing the 1/4-20 bolt. 5. Re-install the new igniter into the chamber using the bracket.

6. Inspect the igniter from the front of the unit by removing the firepot and looking into the end of the chamber.

MAKE SURE THE IGNITER IS CENTERED IN THE CHAMBER.

pellet stoves for heating Christmas gift holiday thankgiving

R. Duggan
Reviewed in the United States on March 3, 2025
Installed, looked like original, fired right up. I can’t say what the longevity is because it’s brand new but it looked exactly like the stock unit. I bought 2 in case of another failure. Glad I found it here👍🏻
Tweakes182
Reviewed in the United States on February 25, 2025
Very cost-effective replacement parts; the OEM ones are outrageously expensive.
Kindle Customer
Reviewed in the United States on January 14, 2025
Worked as intended
David Purcell
Reviewed in the United States on February 13, 2024
Works well no problems nice long wire to help installation
Sarah Brander
Reviewed in the United States on December 4, 2024
Lasted on month. Install was easy, worked great until it didn't.
Joseph P. Coffey
Reviewed in the United States on December 30, 2024
Bought for spare.
Plow king
Reviewed in the United States on October 28, 2024
Worked as it should
Gregory C. Robinson
Reviewed in the United States on November 4, 2023
Fifteen fin igniter fit in carrier with a little gentle persuasion. Lots of wire lead if needed. Worked well after install.
Barry Stringer
Reviewed in Canada on March 23, 2022
It was like brand new. Barry