Your cart is empty.
Your cart is empty.From the Manufacturer
This sturdy universal tool stand measures 24-Inch tall, 27-1/2 by 31-1/2-Inch at the base and 17-3/4 by 22-Inch at the top. Includes non-slip rubber'. 1,000-Pound capacity.
The perfect key for a great tractor
Reviewed in the United States on March 2, 2025
Easy assembly very heavy duty. I’m pleased
LucyB
Reviewed in the United States on March 11, 2025
The directions were missing so it took a bit of interpreting. Quality is mediocre. The metal so light duty. I doubt 1000 lbs could be on top! Also so much lower than I thought! I’m short and it’s too low for just about anything!
Deborah Foster
Reviewed in the United States on February 12, 2025
fast shipping
Jim Brown
Reviewed in the United States on May 29, 2024
As described, sturdy small bench that can be used for many uses. Only small negative was it was missing one flat bolt that I had to improvise, other than that a good purchase for me.
Me
Reviewed in the United States on October 20, 2024
I bought this stand for my Ridgid portable 10” table saw. I added a piece of 3/4” plywood to the top and bolted my saw to it. Rock solid, no wobble, no wiggle. Excellent tool stand.
JimmyCarl
Reviewed in the United States on July 15, 2021
Assembly drawing has some errors & no written instructions, on par for China produced items.BUT, the stand was much better than expected on tolerances on components from hole locations to length dimensions. Once assembled & tightened it was square & sturdy.All hardware for assembly included and fit nicely. Suggestion would be to use some form of thread sealant since no lock washers included.Paint seems well done and appears not to scratch easily.Only suggestion for improvement is cutting of leg bottom. After install the legs rest only on outer point. Seems strange since unit comes with rubber leg covers for entire leg, but it only sits on corner. This caused me to recut leg ends horizontal to ground since I needed to weld castor wheel mounts. Probably would have cut anyway to have full leg/rubber end ground rest.Bought this as stand for new Smoker & only needed support for 200#'s. Seems more than enough strength for the job.Would buy again if needed.
Larry moore
Reviewed in Canada on October 1, 2021
Well constructed and fit was excellent. Instructions were poor so had to make changes on the fly during assembly
David F. Wallace
Reviewed in Canada on April 12, 2021
These shop fox stands are great. Powder-coated, sturdy, and snugly fitted. A lot of the other tool stands on amazon were just chinesium junk - cheaper perhaps, but of dubious quality. Not so with this stand.Added a plywood deck, and the mounted a Bosch router table on top and it works great - stand is the perfect height.The biggest tip is if you plan on using this for any sort of power tool base, it's worth using a bit of threadlocker rather than reefing down on all the nuts. This will keep anything from loosening from vibrations.
Josh
Reviewed in Canada on August 26, 2020
I bought this stand for my Ryobi BT3100 table saw. The saw is about an inch larger than the stand so I put a piece of 3/4 plywood on top. The stand comes with mounting holes for a top so this was very easy. I hand tightened the bolts and then went back over them with a drill to tighten them up.Very pleased with this stand and it seems quite versatile in its application.
MikeyJoe
Reviewed in the United States on July 10, 2019
Receive this stand today. Packaging was compact and pieces were placed between packing paper so no rubbing occured to the paint during shipping. The paint is good quality and appears to be very durable. Instructions were a single sheet of paper showing layout of assembly, but should not be a problem for most people. If the instructions confuse you...perhaps your not ready to use the power tools this is meant to support...my opinion. The bolts, nuts, and washers were fine with no problems. I was disappointed by no lock washers. Note to Shop Fox: Include lock washers. Everything else was great quality...so why skimp on lock washers? Have a talk with that bean counter who made that decision. Lock washers are essential on a product that will be subject to a lot of vibration. LOCK WASHERS!!! Ok...I made my point.Overall I will buy again if I should need another stand in my shop...which is likely.
R. Wilcox
Reviewed in the United States on June 10, 2019
This is a great sturdy stand. I would have given it 5 stars however, it does not come with instructions. It only has a line drawing showing the assembled stand. It's pretty straightforward to build....just lay everything out and group the pieces together by style and size and you'll get it. Some have complained about the hardware. I got lucky and only had one wonky bolt that had excess metal from the machining process. I used my Dremel to file it down and it fit perfectly. It is a heavy stand but I don't plan on moving it around much. I can pick it up along with my attached RIGD R45171NS and get it out onto my driveway fairly easily. I may add some retractable casters at some point. For now, it's a very stable base on which to bolt my table saw. The height is perfect and brings my saw up to the perfect work height. I highly recommend this table as it can be modified for different uses. I have attached pics of how I attached a piece of MDF to the top and bolted my saw to that. I only had long bolts for the saw so you'll see those extend down below the top. I have to get shorter ones eventually.
GUILLERMO ACEVES MORA
Reviewed in Mexico on May 31, 2019
La utilice para una sierra de banco portátil y la verdad que es ta muy buen , muy fuerte para soportar la sierra y a la ves muy lijera.
Marlo
Reviewed in Mexico on July 4, 2018
La mesa Shop Fox D2275 esta bien diseñada y fabricada (en China por cierto). No trae instructivo pero es facil de armar. Tiene buenas dimensiones . Hace tiempo compre una mesa similar marca "Craftsman" pero es mas pequeña en Largo x ancho y de altura similar. La D2275 es mas amplia en su base y en la parte superior lo cual la hace mas estable y segura. Actualmente uso la D2275 para soportar un taladro de banco. Nunca voy a rebasar la max. capacidad de carga de esta mesa (1000 libras = 500 kg). La unica observacion negativa que puedo compartir es acerca de dos las patas que observe que tenian un muy ligero arqueamiento. Pense que eso iba dificultar el armado, pero no fue asi. La recomiendo ampliamente. Tomen en cuenta las medidas para no tener problemas de espacio.
Recommended Products
$105.46
$ 47 .99 $47.99