Your cart is empty.
Your cart is empty.Simple Deluxe air pump, widely used to supply oxygen in aquaculture, pond and hydroponic systems. Includes chrome air manifold and 6 air outlets. The cylinders and pistons are made of high-quality wear-resistant materials to make the pump body durable. Easy to operate, quiet and oil-free, the best ideal air pump.
O.P.
Reviewed in the United States on March 16, 2025
Powerful no problem at all
Kevin B.
Reviewed in the United States on March 1, 2025
Workhorse. It's not quiet but not loud. It pushes a lot of air and runs a tad warm. Does what it should
Tricia
Reviewed in the United States on September 5, 2024
I ordered the pump to use on my aquariums for ease of use. It seemed to be a very powerful and efficient pump, which I tested for only about 5 mins, when i received it just to make sure the power and air flow worked. When I was ready I did my set up and all the necessary connections to my tanks, however the pump only stays on for about 20 minutes, it gets hot and shuts down. My window to return the pump has closed because I did not use the pump within close proximity of receiving it. I'm a bit disappointed cause now I'm back to square one.
Arturo Colombres
Reviewed in Mexico on June 9, 2024
Yo compré esta bomba para mi máquina laser, no para pecera. Por lo que mi opinión es solo por si estás buscando algo como esto para máquina laser. Evidentemente mis cortes mejoraron. Sigo usando dos pasadas en cortar, pero es 100% seguro que a la segunda pasada mi laser corta excelente. Incluso cuando el laser está recién limpio, corta el mdf a la primera gracias a la bomba. En mi caso corto a 300mm/s a 80% de potencia, o a 287mm/s a 80% de potencia. Otra ventaja es que al usar aire el lente del laser no se ensucia tan rápido, por lo que aguanta muchos proyectos cortando antes de limpiar el lente nuevamente. Recomiendo que no se use el adaptador de varias salidas, ya que esto reduce considerablemente la presión del aire, y para el laser se nota mucho. Repito, esto es solo para los que usamos esta bomba para corte láser. Podría necesitar mas presión y tener un mejor desempeño en mis cortes, pero por lo pronto con esta bomba me va muy bien. Ojo, tienes que comprar la de 58W, para que te quede excelente.
Pilgrim
Reviewed in the United States on May 4, 2024
I'm using this pump to provide the air for three five-gallon buckets of my hydroponic garden. Yes, the pump is loud so I use a Styrofoam lid to help absorb the noise. The lid is several inches away from the pump and doesn't not cover the pump. The pump is powerful. I use three of the outlets and do not have any of the outlets completely open. IMO the pump would handle at least five five-gallon buckets. Mine runs 24 hours a day. It's located in the basement so no noise is heard upstairs. With the muffling, I've learned to ignore the noise and just enjoy watching the tomatoes and pepper grow. My desk is about 10 feet away from the pump. I'm often on my phone and I've never had a comment about the background noise.
Checkfx
Reviewed in Canada on May 11, 2024
Très efficace !Chauffe énormément parcontre comparé a un modèle 800 Gph. Même le outlet a valves devient brulant !
Ezequiel
Reviewed in Mexico on March 26, 2024
Sii
Sam Barrese
Reviewed in the United States on March 21, 2024
I got this to make bubbles in my toddlers bubble bath. I was tired of manually have to keep agitating the water to make more bubbles so I decided to try this. Works pretty good I have to say. My toddler now has bubbles the whole bathtime and I can still feel my arm at the end. It has a distinctive hum to it. Not super loud, but noticeable. Kind of the same noise level as a vacuum sealer. We only run it for 30 minutes or so and I haven't noticed any heat build-up in that amount of time. The outer case is warm but not hot.I was having a hard time figuring out what size pump I needed for this. This is sending air to two 8" long rubber bubble tubes and use the1030 gph pump. This seems to work well for making bubbles in the bathtub. Could probably go down a size for the pump and still be fine.
Chris
Reviewed in the United States on February 7, 2024
These are unbelievable, compared to ordinary aquarium pumps you usually see, the pumps I was previously using were rated for 30-60 gallon tanks. These seem to move 10x the air. As some have mentioned, they're fairly loud, but so are NASCAR cars compared to your family car. I probably wouldn't want to use one in my living room or bedroom, but in the application I'm using it for, it's not an issue. 10 stars for my purpose, the water looks like it's boiling, and I only have 4 of the 6 outlets hooked up. High quality soft rubber hoses included, unlike the hard plastic usually supplied, very easy to get on and off fittings.
Peter J. Benjamins
Reviewed in the United States on September 6, 2022
I am using this pump for a laser engraver air assist (to blow air over laser beam burn point to blow fume particles away from laser lens and material being engraved or cut). I was surprised how quiet it is for this purpose in a garage or shop. Late night operation is not heard in an adjacent room separated by simple drywalled wooden stud walls without insulation. (The hum might be objectionable in a quiet bedroom or livingroom.) The unit is well designed acoustically as I could not find a way to reduce the noise by grasping, squeezing, hanging, or placing it on foam or rubber pads. If the noise is objectionable, the only way to reduce it would be to isolate it (enclosing or relocation) It blows plenty of air but it has almost no air pressure. If your hose has a kink, or high airflow resistance, it will not deliver air. Placing my finger over the hose ends offers no resistance at all.It is surprising considering the volume of air delivered with the hose end uncovered.
Gerald
Reviewed in the United States on April 21, 2022
Saw one of these unit recommended by a number of CNC Router users for air cooling and/or mist cooling in lieu of a much noisier compressor. For this use, the bore of the outlet port needs to be drilled out as far as your courage to reduce the air restriction as much as possible, which I did, and it is doing a fine job for me. The noise of the unit is much reduced as soon as it is pushing against a restriction (even just tubing) versus the unit running naked of any connections. Then, for my use, the noise disappears as soon as the spindle gets above 8K rpm, the end mill hits the Aluminum, or the control box heats up and any of the other cooling fans kicks on. Regarding the unit getting hot, I've never touched it, as I'm more concerned keeping the end mill, drill bit, and/or workpiece cool and working or being worked.Would definitely buy again, and likely to buy more for other cooling or low pressure operations.
Barn
Reviewed in Australia on August 27, 2021
Had been looking forward to running ALL my airstones from one pump. I'd should of known that it wasn't going to work!!! Set it all up as per instructions, plugged it in, after ONLY 5mins started to smoke then stopped working ,blew up and tripped my safety switch.GOOD ON YER CHINA!!!!!
Peter
Reviewed in Australia on October 19, 2021
Just like other Australian reviewers, pump burned out after 5 minutes of use.To the seller: PLEASE update your listing to reflect this is a 110V pump! I only discovered this AFTER it started spitting out smoke. I really wish I checked the markings before I plugged it in.This pump to work in Aussie market also needs a 240V -> 110V transformer.
Recommended Products
