Your cart is empty.
Your cart is empty.Product Description
Threads built to last
Our proprietary manufacturing and metal treatment processes ensure that threads will hold up even under the most extreme conditions found in seized u-joints.
The right fit
Each glove is cast to ensure the most universal fit possible while still maintaining strength to tackle even the most stubborn jobs.
Made in North America
Over the past 30 years, our dedicated engineers and machinists have manufactured tens of thousands of U-Joint Pullers right here in North America, many of which are still in service to this day.
Find The Right Fit
To find the right fit, measure your bearing cup and reference the below measurements to determine what Tiger Tool U-Joint will work best.
- x = 1.5" - 2.2" : Heavy Duty U Joint Puller (Kenworth, Peterbilt, Freightliner)
- x = 1.25" - 1.7" : Intermediate U Joint Puller (F-650, International Durastar, Isuzu NRR)
- x = 1" - 1.25 : Automotive U Joint Puller (F-250, Toyota Tundra, Ranger)
tom
Reviewed in the United States on March 20, 2025
100% legit company. Strong tool well built. Makes jobs much easier! Worth the investment. I believe it will last a lifetime.
Michael Searing
Reviewed in the United States on January 21, 2025
I recently used the Tiger Tool U-Joint Puller for the front axle U-joint replacement on my 2015 Ram 2500, and I have to say it made the entire process incredibly easy. I had heard a lot about these tools, but nothing compares to experiencing it firsthand.Gone are the days of struggling with a hammer and blow torch. The puller is built solidly, and the design is simple but effective. It applied even pressure and quickly popped the U-joints out. The tool fit perfectly on my truck, and I didn’t have to fight with the tool or worry about damaging anything in the process. Worth the price! Buy once, cry once
Consumer
Reviewed in the United States on September 24, 2024
I have the smaller one that works well for 1350 U-joints. 1480 U-joints was a bit of a stretch for the smaller one so I stepped up to the next size and it works just as good.
Kyle Heron
Reviewed in the United States on August 22, 2024
Been using a ball joint press and various sized sockets for years. Worked good but always cumbersome felt like I always needed a 3rd hand to hold everything in place and wouldn’t always fit in tight places if doing on the vehicle. This made life so easy. Had the ujoint out in a few minutes, longest part was getting the rusty clips out.
Brian
Reviewed in the United States on July 21, 2024
We were able to remove front axle u joints on a 2005 f350.
Timbitbran
Reviewed in Canada on March 24, 2024
Doesn't fit on anything. Never used it and never will but to late to return.
Darryl
Reviewed in Canada on February 11, 2024
I bought the tiger u joint puller and was impressed with it on first joint but was easy one then the second was ceased in and had impact in it and thought something was going to break but nope it worked perfectly would totally recommend this tool
Cody
Reviewed in Canada on July 1, 2021
Worked great in dodge 3500 wheel unjoint.
B. Thornton
Reviewed in the United States on January 29, 2020
I used this tool on a 2003 Dodge 3500 4WD front axle U-joints. The tool is certainly heavy duty and I can't complain about its strength and durability, that part is impressive. For this particular truck, it doesn't work out so well. The American Axle U-joints for this axle are pressed in with very tight tolerances. In addition, they rust and seize in place. This tool will push them out, but unless you are very careful and use a torch to heat up the yoke (use LOTS of heat), you end up damaging the yoke as you push out the U-joint caps. You would think the huge, heavy duty yoke would not bend, but I destroyed 2 sets of U-joints trying to press them back into the yoke because the ears on the yoke were spread apart and didn't align properly. It is not the tool's fault that this happens, it is just doing its job. In fact, the tool is so strong that it broke one of the U-joint caps when I was pressing it out. I had to use a torch to be able to press out the remaining piece of the cap, but the tool did its job properly. I ended up buying a replacement axle shaft with the U-joint already installed because the yokes on the old axle shaft were damaged in the process of pressing out the U-joint. Because of that, I paid almost $200 for this tool and it was a waste. As far as value for the money, this tool is way overpriced now that there are other tools out that will do the same thing.
Justin K.
Reviewed in the United States on April 7, 2016
Absolutely amazing tool! I'm an automotive tech by trade, so I buy a LOT of tools. My personal F350 needed the front axle shaft u-joints replaced. Dana 60 axle shaft joints, especially after 25 years of time to rust in place and seize up are notoriously difficult and usually either laugh in the face of even large shop presses. Or, they'll send whatever setup you use to press them flying across the shop/into your face/into the neighbor's yard without budging. This tool though, this thing allowed me to remove a badly stuck, rusted in joint in under a minute with ZERO damage to the shafts or myself. Unlike lower end puller/pressing tools, the forcing screw on the Tiger Tool is fine threaded and very hard, no galling or shedding threads in sight even after winding it up as tight as a 1/2" Snap On Cordless impact would twist it. I'm almost looking forward to do doing the other u-joint with this thing in my arsenal!
Recommended Products
$200.98
$ 89 .99 $89.99