Your cart is empty.
Your cart is empty.Product Description
7.3 Injectors Sleeve Cup Removal Installation Tool
Fitment:
- for Ford 7.3L Power Stroke 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003
- for Navistar T444E, DT466E Diesel Engines
- for Caterpillar 3126,3126B,3126E Diesel Engines
OEM Part Number
- Replace for Injector O-rings Number: XC3Z-9229-AB, XC3Z9229AA, CM-5010, 1833564C92, 1833564C91, 1823492C97
- Replace for Injector Cup Number: F4TZ-9F538-A, F4TZ9F538A, 1814376C1
Parcel Including:
- 8x Sleeves
- 1x Fuel Injector Sleeve Installer
- 1x Fuel Injector Sleeve Remover In-Vehicle Alternative
- 48x Injector O-Ring and Seal
Keishat6
Reviewed in the United States on February 12, 2025
Used the tool and it broke before the job was even complete
Dewayne(Crash)Whitner
Reviewed in the United States on February 23, 2023
TOOL DONE GOOD EXTRACTED THE CUPS BUT O-RINGS ARE USELESS YOU CAN SEE THE MOLD MARKS ON THEM DIDN'T EVEN TRY TO USE THEM WAS AFRAID THEY WOULD FAIL
James
Reviewed in Canada on November 20, 2022
Honestly scared to use the tool and seals due to reviews. Went and bought factory motorcraft orings and will buy motorcraft cups too....its just not worth the risk to install after reading what everyone ellse said and after watching multiple videos from trusted 7.3 builders
Customer
Reviewed in Canada on November 14, 2022
So, my 7.3L was putting diesel into my coolant. Obviously cups are gone, ordered this inexpensive set off of Amazon, got to the job, install and removal was extremely simple, just needed a wrench and pry bar. Install went amazing. Couldn't have been easier, can't be happier.
SB
Reviewed in the United States on June 5, 2021
The removal tool sucks, it broke inside the first cup I was going to remove. It was almost impossible to pull out of the the injector sleeve. Took me hours to remove the broken tool.
Tracy Miller
Reviewed in the United States on June 1, 2021
I wish I could give negative stars!! These are the o rings that came with this kit, after only 400 miles. TWICE I've had to get towed from jobs I was working due to all of the 4 gallons of oil my truck holds going into my fuel tank, and causing my engine to run dry. The first time it happened after only 200 miles, and I found one of the o rings deteriorated. Thinking it was just one poorly manufactured o ring that made it past QC and into my set, I just replaced it with a Ford OEM o ring. Then, 200 miles after that, truck broke down with same issue, no oil in engine and all of it in my fuel tank. Had it towed again, and took out every injector, and this time ALL the remaining 7 of the o rings from this kit were deteriorated just like the first one!!! I literally had to fish pieces of these o rings out of my injectors! There is now extensive damage done to my engine, and I am out a lot more money and time than if I had just bought a Ford OEM injector kit! Not to mention the embarrassment of having to get towed from customers properties and leaving jobs unfinished while my truck was down. Do yourself a favor and don't try to go cheaper when it comes to your vehicles, especially crucial components. And as for this company, IF YOU'RE NOT GOING TO MANUFACTURE PARTS THAT WORK, THEN DON'T MAKE THEM AT ALL!!!!
Ace Reefer
Reviewed in the United States on May 22, 2021
Took a while to get here And when it shows up the head on the Bolt is completely stripped. It looks like They are reusing old Bolts. The job didn't come in till about 2 weeks 3 weeks after I receive product so when I finally opened it it was too late to even get a replacement Tool. Contacted Seller and they were not even helpful even with the pictures. Buyer beware
Jaustin2017
Reviewed in the United States on March 31, 2021
The media could not be loaded.
Carlos pelayo
Reviewed in the United States on March 20, 2021
Excelente inversion
Maria castro
Reviewed in the United States on April 4, 2021
Good
Recommended Products