Your cart is empty.
Your cart is empty.Product Description
BILLFARO Universal Motorcycles Cruise Control Throttle Lock Assist
Specifications:
Material: High quality nylon and rubber
Package Included :
1 x motorcycle cruise control throttle assist set
3 x Hex Key
1 x Replaceable Screw
Feature:
1.Suitable for 7/8" and 1" handlebars for motorcycle OEM grips
2.Motorcycle grips with minimum 1 1/8" to maximum 1 3/4" outside grip diameter
3.Interchangeable rubber inserts is allowed to be used for most motorcycle grip accessories (including some electric motorcycles)
Note:
Technically this cruise control universal for motorcycles. Please check our dimension diagram and measure your motorcycle handlebars to make sure it can fits.
Step
Step 1:Read understand all steps in the instructions before starting the installation.Park the motorcycle on a hard,level surface.turn off the ignition and allow the engine to cool.
Step 2:Slide the nylon collar assembly with handlebar top clamp over the end of the throttle.Loosely fasten the handlebar bottom clamp to the top clamp around the handlebar.
Step 3:Determine if the arm spacer will be necessary.The arm spacer will need to be used if the standard length arm does not clear the handlebar controls and allow the handlebar top and bottom clamp to wrap around the handlebar while the nylon collar assembly is around the grip.
Step 4:Select correct rubber collar(small ,medium or large).Test fit the rubber collar around the grip.The collar should fit around the grip without a large gap or overlapping ends.
Step
Step 5:Insert the correct sized rubber collar between the nylon collar and grip.Place the “joint’’of the rubber collar on the bottom side midway between two set screws on the nylon collar.Tighten the top /bottom clamp around the handlebar.
Step 6:Twist the throttle to ensure there is no binding and the throttle will return to the closed position.Make sure that the tension collar is in-line with nylon collar and grip,incorrect adjustment may cause the throttle to stick in the open position.
Step 7:Rotate the throttle assist arm and thumb lever to the desired position.Retighten the top/bottom clamp in desired position .The thumb lever should bein a position for easy access.
Step 8:Tighten the 3 set screw on the nylon collar until the screws are flush with the collar.
Alexis
Reviewed in the United States on July 14, 2024
Once I was able to get my handel apart to fit it over the grip and got it installed which wasn’t too terrible I was ready to test it and tink something broke and flew off. The rod that clamps the band around the grip flew off never to be found. I was able to rig up a replacement but then as I’m testing my replacement part that I had to make myself the screw that holds the thumb lever backs out the screw every few times you press it so I guess I’ll JB WELD the screw in because going through the hassle of replacing a product sucks!! Way to go
gary pearson
Reviewed in the United States on July 12, 2024
Easy to install. It holds the throttle as it should, and allows the throttle to return when released. Came with a spacer if needed(I didn't) three different sized ru ber grommets for the throttle, and spacers(0mif needed) for the handle bar connection.
David
Reviewed in Mexico on February 27, 2024
Los materiales son de plástico, cumple con la función es de regular calidad tube que hacer muchas adecuaciones a los puños pero al fin quedo si tienes puños originales no batallaras, mi moto es una VTX1800 Honda (funciona)
Tom Bungay
Reviewed in Canada on October 9, 2024
Works wellGreat for long rides.
Kindle Customer
Reviewed in the United States on October 14, 2024
It moves around a bit to much and seems to me the inner rubber isn't grippy enough. It loosens up a bit and it's not working great. I'm sure more adjustments will help it, but it's a lot of work to set it well.
shaltryk
Reviewed in the United States on August 3, 2023
Worth the money I spent! I took my time and put this on my bike. Because it is a universal throttle lock, you do have to make it fit your bike. I ended up sawing 1/3 of the spacer to install it and it fits perfectly. I used it last night on a quick 50 mile ride and t worked great! I had one of these on my last bike and it helped out a lot with being able to stretch your hands out on a long ride and getting rid of some of the numbness from gripping too tight. Definitely would buy again or for a friend.
Randy Justice
Reviewed in the United States on February 18, 2023
For the price this is a really good product, with just a few minor improvements, it could be a GREAT ONE !!! First it needs to be made out of billet aluminum, second it needs more throttle adapter sizes, and third, it needs a clamp on the center extension, I used a 1/4" hose clamp over a piece of vinyl tape to stiffen it up. I would be willing to pay $10 or $15 more for these improvements. I really wish the manufacturer would get in touch with me, I believe I could help them greatly !! Works OK though, not junk like a lot of these throttle locks, just could be made BETTER.
OhmaTokito
Reviewed in Canada on April 26, 2023
The media could not be loaded.
Terry Webber
Reviewed in the United States on April 18, 2023
The installation required a little work but nothing that bad. My only complaint is that the directions were printed in a font that was way too small.Looking forward to many miles.Update... Just ordered a second one for a friend who had to have one after our first ride.
Michael Paal
Reviewed in Canada on April 16, 2023
I tried it but it was temperamental to install and quite fragile , the bikes vibration would cause it to back off while riding causing you to lose speed .
Darryn
Reviewed in Canada on July 15, 2022
Very easy to install, seems to be VG quality. Easy to use with the flick of the thumb, easy to adjust if it slips from vibration.
KJug Guitars
Reviewed in the United States on January 2, 2022
First of all, this is a very efficient throttle lock for the money. I've had throttle locks in the past (waaayyy in the past, mid 80's) and this is definitely a better mechanism.The instructions are... well... not really helpful. Lots of pictures showing you the parts, but this ain't your paint by numbers kit!It's a pretty straightforward process. On my Himalayan, I had to move the mirror/brake reservoir assembly a bit to create space for the support bracket. 7/8" handlebar spacers work just fine.Construction: Built well and it should last. The moveable parts are going to be hard to wear out.Function: I've got the three Allen screws in tight to put the collar on the handlebar grip, and I've got the spring tension set so I get the throttle to snap back to "zero throttle" once I thumb the lock to "off". When locked, there is a little throttle creep that will reduce rpm's before it settles to "locked". I may tweak the spring tension a little more and see if I can get it to hold immediately, and release just as quickly.Price: Hard to beat for what you get.Instructions: It's more of a general guide, but it's not hard to figure out once you've read it. Just make sure you put the thumb lock screw through the "eye" of the screw the spring goes through (my "aha!" moment).If you ever ride constantly between gas stops, your right wrist will appreciate this throttle lock.
Recommended Products