Your cart is empty.
Your cart is empty.UTG Pro 30mm/2pcs medium profile p.O.I Picatinny rings. Features: - medium profile p.O.I (precision optics interface) rings have a 30mm center height to fit optics with a 30mm tube and up to a 59mm outer objective - the innovative p.O.I (precision optics interface) addresses 3 of the most critical areas in scope rings - a) progressively machined for a precise inner ring surface to achieve a seamless ring-to-scope interaction b) low profile and flush-fitting locking side plate controlled by dual spring loaded guide rods interfacing with the rail with torx screw locking to ensure secure and repeatable zero hold C) square-shaped integral recoil stop interfacing with a Picatinny Slot via complete surface contact to eliminate the possibility of forward and aft movement from recoil vibrations - 2 pieces ring set, each equipped with 4 top torx screws and designed with a 22mm ring width - designed to fit on mil-spec 1913 Picatinny rail platforms - machined from 6061-T6 aluminum alloy and 4605 steel with matte black hard coat anodize - UTG Pro original snag-free contoured profile with reduced weight and size. Specifications: - material: aluminum/steel - weight: 2.6 oz - pieces: 2 - rail type: Picatinny - profile level: medium - ring diameter: 30 - ring width: 22 mm - max. Scope outer Dia.: 59 mm - screws per ring: 4
Thomas Maiworm
Reviewed in Germany on April 1, 2022
Gute Qualität!
Franklin VanWhy
Reviewed in the United States on July 3, 2019
Needed new rings for my Long Range competition rifle. Saw these and heard good things about them. After receiving them I installed them on my rifle with ease. They are very sturdy and look well made. Fit was great on the rail and with the scope tube. The machined in stop for the cross slot is nice! I would definitely buy again. The medium height rings had the perfect clearance for a 10-50 x 60 Sightron SIII with an 1.25" straight barrel. And they are made in the USA!!
Daniel Geisinger
Reviewed in Germany on December 30, 2019
Sehr robust und massiv. Macht einen sehr tauglichen Eindruck und lässt mich auf meiner 308 nicht in Stich.
David Strong
Reviewed in the United States on December 13, 2019
These rings are super heavy and put scratches on my scope. There are much better options out there.
CainOhana
Reviewed in the United States on January 18, 2019
These rings are very high quality and gives the big boys like Seekins and Vortex a run for their money. I think Vortex realized and came out with their Pro line to compete against these, but not fully available on Amazon yet. Don't hesitate, buy these rings if you spend good money on a optic, you won't be disappointed!
John Parra
Reviewed in the United States on August 21, 2018
Can't believe the great level of workmanship for the price. Was kind of wary of the low price but, the item is more than worth the price!
andy nading
Reviewed in the United States on December 18, 2018
Best looking and functioning scope rings ive found especially for the price
Great Brown Hunter
Reviewed in the United States on September 16, 2017
Didn't like how the bar that goes through the rail or scope base isn't solid across the bottom, it goes half way leaving it able to twist a little which I can see being a problem when out in the field.
A. Prill
Reviewed in the United States on May 1, 2017
These are extremely well made and are inexpensive when compared to other precision scope rings. I returned these rings because they were too high. Leapers/UTG rings do run on the high side but I over estimated when ordering. I exchanged these for low rings and my full review will be for them.
David W.
Reviewed in the United States on November 14, 2017
The UTG Pro 30mm Medium profile rings appear to be very well made. Threading is tight, rings mate up very well, locking mechanism for picatinny system is smooth. However, they are not even remotely close to the correct/standard height for medium rings. They are WAY too high. I took them down to the local gun shop and compared to Leupold's and Weaver's models (30mm tube, picatinny rail, medium height), the UTG is a 1/4" taller saddle height. I didn't have a micrometer handy...as it turns out, I didn't need one. I could use a tape measure. I compared the UTG to a large Leupold and Weaver ring and the UTG is taller then those as well. I would exchange for a low ring, but I'm not confident a low would work. I'm giving it three starts because the product looks well built, however be forewarned the sizes are WAY off. Good luck
Recommended Products
