Shopping Cart

Your cart is empty.

Your cart is empty.

UTSAUTO Oil Drain Plug Gaskets Crush Washers Seals Rings Part # 90430-12031 for Prius Tundra Sienna Highlander Scion Corolla Rav4(12mm) 12 Packs

Free shipping on orders over $29.99

$4.99

$ 1 .99 $1.99

In Stock

About this item

  • O.D.(outside diameter): 21 mm /0.82 inch, I.D.(inside diameter): 12.2 mm / 0.48 inch , Thickness: 1.85 mm / 0.07inch
  • This oil drain plug gaskets crush washers is for Prius Tundra Sienna Highlander Scion Corolla Rav4(12mm), see more vehicle fits in the description
  • This 12.2 mm / 0.48 inch oil drain plug gaskets crush washers is needed for every oil change, it helps to seal the drain plug and oil pan surfaces.
  • This is the direct replacement for the part# 90430-12031 , package including 12pcs oil drain plug gaskets crush washers
  • High Quality: Our washers are made with high quality materials, design and produced by the original washers ,can directly fits your cars



Product Description

toyota drain plug gasket 9043012031 90430-12031 tundra oil plug gasket

  • 17-18 Prius Prime , 12-17 Prius V
  • 96-18 RAV4 , 01-18 Sequoia
  • 98-18 Sienna , 99-08 Solara
  • 93-98 Supra , 93-98 T100
  • 95-18 Tacoma , 90-99 Tercel
  • 00-18 Tundra , 09-17 Venza
  • 06-18 Yaris

UTSAUTO 90430-12031 Oil Drain Plug Gaskets Crush Washers Seals Rings

Fitment:

  • 2011-2017 CT200h , 2006 GS300
  • 2007-2011 GS350 , 2006-2007 GS430
  • 2007-2011 GS450h , 2013-2017 LS460
  • 2008-2016 LS600h , 2015-2017 NX200t
  • 2015-2018 NX300h , 2015-2018 RC F
  • 2016-2018 RX350 , 2016-2018 RX450h
  • 1992-2000 SC400
  • 2016 iM , 2012-2015 iQ
  • 2005-2016 tC, 2004-2006 xA
  • 2008-2015 xB , 2008-2014 xD

  • 90-18 4Runner , 95-19 Avalon
  • 89-18 Camry , 90-05 Celica
  • 17-18 C-HR , 85-18 Corolla
  • 17-18 Corolla iM, 85-90 Cressida
  • 00-05 Echo , 07-14 FJ Cruiser
  • 01-18 Highlander , 91-18 Land Cruiser
  • 03-14 Matrix , 85-95 MR2
  • 00-05 MR2 Spyder , 92-99 Paseo
  • 90-95 Pickup , 91-97 Previa
  • 01-18 Prius , 12-18 Prius C

toyota drain plug gasket 9043012031 90430-12031 tundra oil plug gasket

  • O.D.(outside diameter): 21 mm /0.82 inch
  • I.D.(inside diameter): 12.2 mm / 0.48 inch
  • Thickness: 1.85 mm / 0.07inch

toyota drain plug gasket 9043012031 90430-12031 tundra oil plug gasket

This oil drain plug gaskets crush washers is for Prius Tundra Sienna Highlander Scion Corolla Rav4(12mm), see more vehicle fits in the description

toyota drain plug gasket 9043012031 90430-12031 tundra oil plug gasket

Our washers are made with high quality materials, design and produced by the original washers ,can directly fits your cars


Rick
Reviewed in the United States on August 3, 2023
no much to say, other than they work. no problems...
Stephen
Reviewed in the United States on May 20, 2023
Perfect for Toyota oil change.
R. Treadway
Reviewed in the United States on March 2, 2022
Great price for “crush” washers. The fiber does most of the sealing, I think. Swapped out the original GM plug for a magnet plug, this fits great. The outside diameter is a little smaller than the flange on the plug but that’s ok. I used the Votex “Made in Wisconsin” plugs sold on here, flange is same size as stock GM plug, and this washer is the same size as the original rubber washer. Torqued to factory specs (25 Nm) was no leakage when first installed. Just finished a 300 mile trip, no leaks, no drips, it’s holding up! I will drill it out a little for the 1/2” plug I have. 1st pic is this crush washer over a copper one, second is copper over the OEM plug to show coverage. The aluminum washer at the bottom is what comes with the Votex plug. You can see the copper washer is a (very) tiny bit larger. Edit: Drilling it out isn't as easy as I thought, a 1/2" bit just digs in and snags the aluminum, so I started with a 15/32" bit and reamed it while holding it cupped in my fingers. Use the 1/2" bit to determine the finished size. A 31/64" bit is a snug fit in the original hole, but my 15/32" bit worked better, i think it was sharper. Edit 8/23/22: I just did an oil change on the second vehicle, and the drain plug was loose! I could take it off by hand!! Both vehicles had this issue, I thought the first one might be a fluke, but the second confirms the issue. I tightened both to factory specs with torque wrench 25 n/m (18ft/lb). There is some kind of brown fiber pieces around the edge of the gasket, both had that. It wasn't leaking, and I'm amazed it had't fallen out. The one vehicle went 5,700 miles, the other 3000. I am using the Votex Stainless Steel Plug with this, so not sure if this is a gasket issue, or a plug issue, but I would assume the gasket. I reused the plug with a new gasket, this time torquing to 40n/m (30ft/lbs). I think I felt the gasket crush, so hopefully it stays tight. I will check back in next oil change which will be in November. Edit 10/12/22: After torquing one new gasket to 40N/M it was loose again after only 15miles. The plug was hand tight. The other vehicle I torqued tighter also was loose. Apparently these do not have enough friction to keep the plug from loosening. See the two pics I added, the glue that holds the fiber onto the aluminum melts with heat, the fiber wafer easily peels off of the surface. Maybe the glue has failed and allows the plug to turn, I can't verify the cause, but I do know that the plug loosens up after a very short time. I DO NOT RECOMMEND THIS PRODUCT.
Mitchell Thompson
Reviewed in Australia on November 17, 2022
Good gear, they fit well.
Henry
Reviewed in the United States on September 12, 2021
Quality and price!
Brian M
Reviewed in the United States on August 30, 2021
Smart to provide an reusable zip lock envelope with the product label on it: easier to find for next oil change. With the label, easy to tell apart from other crushable washers for other vehicles. This little extra effort in packaging made our life easier and less chance of error. Better than the hard, clear plastic packaging you have to break apart and can't retain the washers in except to re-tape. And who has tape handy that works on that hard clear plastic packaging?
N. Santos
Reviewed in the United States on August 12, 2021
Worked for Prius 2011 and Corolla 2014 for the annual oil change. They worked great.
invenio
Reviewed in the United States on June 27, 2021
Seems to have worked well. Installed a few months ago and no oil leak.
tinh truong
Reviewed in the United States on November 24, 2020
I love it
Recommended Products