Your cart is empty.
Your cart is empty.Designed to fit, perform and sound like the original system, Walker® resonators use precise tuning technologies to deliver excellent flow characteristics and OE-style sound.
Chris Sharp
Reviewed in the United States on October 19, 2024
My first impressions were low when I saw the low quality bends. Not very pretty but this fits PERFECT. The bends are in all the right places resulting in no leaks and no rattles! Great product!
mistymorning01
Reviewed in the United States on October 7, 2023
The part itself is fine, but I had to chop several inches of pipe off to to avoid d hitting an O2 sensor. But after doing that, I then had to relocate the hanger back onto the resonator. I have all the tools and a welder, but this was not a simple remove and replace like it should have been.
lion2929
Reviewed in Canada on August 1, 2020
parfait le transport est super rapide et la piece est ok merci le vendeur je lui donne 10 sur 10
M & S White
Reviewed in the United States on October 9, 2019
I bought this resonator to replace my 2006 Scion xB resonator. I also replaced my muffler with a Walker SS muffler and a new gasket/clamp. The biggest part of the job was getting the old parts off of the vehicle. I had to cut the knobs off of the hanging OE backets. There are two on the OE muffler and resonator. I used a reciprocating saw to cut the old resonator off behind the catalytic convertor. From the reviews I read, I assumed that all of the new Walker replacement parts would fit together and bolt on in 20-30 minutes. It took about 3 times that. First off, I expected the Walker resonator to fit easily onto the 2" OD exhaust pipe behind the cat. It didn't! They were basically the same size. I had to expand the resonator inlet pipe enough to get it to go onto the original exhaust. The tool to do this cost almost as much as the Walker part. I was able to do this manually with much effort. I ended the job by attaching the muffler to the resonator outlet. The two parts with the gasket did not want to go together as tight as the OE parts did originally. It was a pain trying to get them clamped. I did get everything together in the end and noticed no exhaust leaks. I saved a lot of money by doing this myself but, this should have been easier. I should not have been such a pain to assemble the parts and attach onto the exhaust system.
JJ
Reviewed in the United States on February 27, 2018
had a hard time near the cat with that part that connects was a little bigger but made it work. Besides that fit great and works great
Erik
Reviewed in the United States on January 23, 2017
I purchased this for my 2006 Scion XB. It was direct bolt in when used with the Walker 53613 Ultra Import Converter - Non-CARB Compliant
Otherwise you will have to cut the factory exhaust to slip fit this in the factory catalyst. I used the 2 of Walker Exhaust 35335 Hrdwr-Clmp
clamp to seal both halves. The arms for the exhaust hangers are in the correct places and the bends were accurate. I also used the gasket Walker 31577 Exhaust Gasket
the clamp Walker 36519 Exhaust Clamp
to connect to the muffler Walker 54602 Quiet-Flow Stainless Steel Muffler Assembly
Mr. Bill
Reviewed in the United States on August 28, 2015
I was replacing a complete exhaust system on a Scion XB; from the "Cat" back. I also purchased the matching muffler. The installation was pretty easy. I was lucky enough to have the use of a lift. My resonator pipe was rusted out right before the resonator itself. All that needed to be done was to cut off the pipe just before the resonator and to disconnect the clamp that clamps the resonator output pipe to the muffler. Im MY case the muffler was changed as well. You will need a "doughnut" gasket and clamp to transition from the resonator to the muffler. The clamp, also as walker part, is fairly expensive for an OEM style clamp. I don't recommend a cheaper clamp for the job. The resonator simply slips over the existing pipe coming off the existing catalytic converter. Don't cut it too short. This connection can be clamped with a regular "U" type exhaust clamp. A bit of exhaust putty will ensure that there are no leaks.One area which may seem a bit intimidating is disconnecting the old resonator from the rubber mounts. This is best accomplished by using a bit of oil or grease on the area where the "shaft" and knobed end go through the rubber mount. This will help ease them off. If that fails, hack saw the knobed end off. Dont cut the rubber mount. The new part installs easily.Walker is the only company making these replacement parts. They are a good company with a good reputation for quality products. i don't expect this to last as long as the OEM but its not a new car. The OEM lasted 10 years and 150,000 miles.My only wish is that walker would make separate pipes and resonator and muffler, instead of having them welded together as a unit. The fact is that the PIPES where what was causing the problem. The muffler and resonator were still in great shape.Fortunately the cost for the complete units is not too bad when you buy them here on Amazon. These are the same parts that would be used by a muffler shop, since walker is the only replacement. If you can do the work yourself, you will save quite a bit.
yesthatsteve
Reviewed in the United States on March 29, 2014
After nine years and 150,000+ miles in road-salt country, I needed to replace the exhaust in my '05 xB. I went with this unit and the Walker Quiet-Flow muffler, part 54602.To remove the original resonator, I needed to cut the pipe coming from the catalytic converter just before the weld to the resonator pipe. Using a sawzall, it was a piece of cake. This replacement unit was flared just enough to fit over the pipe coming from the cat, and I secured it with the recommended exhaust clamp, Walker part 35335. Fit the original space and exhaust hangers with no trouble at all. I recommend installing this end first, an then connecting to the muffler. You could probably do it the other way, but this order worked for me.Connected perfectly to the new muffler with the recommended clamp & gasket, Walker parts 36519 & 31577. In my opinion, the single-piece clamp is worth the extra cost. A third hand would have been useful to put this joint together, but I eventually got it.Everything works great, and may be quieter than the original exhaust.
Mike
Reviewed in the United States on April 6, 2013
Perfect fit, although the resonator is smaller than the original. Easy to install. Sounds great. Do not forget to buy clamps and gasket.
Recommended Products
$77.99
$ 31 .99 $31.99
$109.22
$ 50 .99 $50.99
$130.67
$ 60 .99 $60.99