Your cart is empty.
Your cart is empty.Enjoy easy access to your hard to reach front and rear valve stems. These durable, nickel plated, brass valve extenders are angled to lengthen your front or rear tire valves. These extenders make checking and inflating your dual tires easy.
PJ
Reviewed in the United States on September 18, 2024
These are the best don't buy the rest.
Scott
Reviewed in the United States on June 21, 2024
Easy to install, other than having to remove the outer wheel. Don’t know of their long term use as aI just installed them, but time will tell, however they appear to be good quality.
SJ
Reviewed in the United States on June 12, 2024
The material seems of good quality. But I could not get them tight enough to stop leaking air. Definitely don't trust them for a trip.
Daniel Caty
Reviewed in Canada on December 18, 2024
Très bien
Herbert M.
Reviewed in Canada on November 7, 2019
I bought these as a spare for my RV, just in case. They are the same type that I installed 2 years ago and they have never leaked any air yet.
Robert
Reviewed in Canada on July 31, 2018
Good quality and perfect for front tires of RV. Stem cleared the Dicor rim cover and plenty long to take PSI of tire without having to remove the wheel cover.
Excell
Reviewed in Canada on April 18, 2018
They both went flat in the winter . But did stay up after tightening .
J-Rod
Reviewed in the United States on May 1, 2017
I installed some new wheels on my bike and had to drill out the hole that I could get the schrader nipple through the presta hole. I was a little worried about this but after doing some research this is common for those of us in the US that can't get tubes at the store with presta valves. I bought these because the nipple just barely come out from the rim. I installed the one of the front and it seem to work fine.
Timbo Slims
Reviewed in the United States on February 27, 2016
These are pictured with the knurling on the threaded part that attaches to valve stem - I was happy to see when these arrived that they actually have a hex bolt style that you can tighten with a wrench. I have had the "finger tighten" type before, and always felt like I was not getting them tight enough - with the ones that arrived I could put a wrench on them and gently get them snugged up where I wanted them.So far so good, they have been installed for a couple of weeks with no signs of leakage. I have not taken an extended trip with them, only short trips, so I will update this review if anything changes or they do not perform as they should.I am using these on my Motorhome, front tires.Thanks for reading
Biker Doc
Reviewed in the United States on December 30, 2016
I was told that the electrochemical reaction from the different metals might cause metal corrosion. I see no evidence of that after about a year. They work great on my SUV with deep hub caps. Far easier to fill the tires, especially in the winter with gloves on. No more bleeding fingers from wrestling the hose connector head into place. No more air loss from bad connections.
Deep Diver
Reviewed in the United States on November 7, 2016
I really don't love it, but I really like them. Fit perfectly, so I gave it five stars. Was easy to install and have no leaks. The top of the valve stems on my new motorhome just come to the top of the dual wheel openings and I wanted to put some TPM sensors on the wheels, so I had to extend the valves. Nice product.
joseph Dean
Reviewed in the United States on January 4, 2016
Mine needed to be cranked real tight to keep from leaking, had to deal with a couple low tires here and there, frustrating. they don't fill very fast either. it was faster to take them off fill the tire then put them back on. I needed these so my tire sensors would fit.
Doug P
Reviewed in Canada on May 30, 2015
I bought these for use in on my Ford at 550. I recently bought 90° bends but they interfered with my chrome wheel covers. The thread for the valve Not the Greatest but They Do Work.
Recommended Products
