Your cart is empty.
Your cart is empty.Product Description
Projector Lamp Type: Projector Bare lamp
Model number: P-VIP 240/0.8 E20.9n Projector Bulb 5j.j9m05.001 5J.J7L05.001 RLC-079
Compatible with Projector models: BENQ W1070 W1070+ W1080 W1080ST HT1085ST HT1075 W1300
Step 1. Unplug the power cord from your projector and let the lamp cool down.
Step 2. Locate the lamp access panel on your projector and remove the screws and access panel.
Step 3. Remove any screws holding the lamp housing into the projector.
Step 4. Reach in and firmly pull the lamp housing out of the projector.
Step 5. Place the new lamp housing into the projector in the same orientation as you removed the old lamp.
Step 6. Wiggle the lamp into place and make sure full contact is made inside of the projector.
Step 7. Replace the lamp mounting screws to secure the lamp into the projector.
Step 8. Replace the lamp access panel and secure the screws.
Step 9. Plug in your projector and power it on.
Step 10. Reset the lamp counter. Some lamps will reset the lamp counter automatically when a new lamp is placed in.
Where is My Projector Lamp Located
A projector lamp can be found by locating a square or rectangular plastic plate somewhere on the outside of the projector; the plate is usually on the bottom of the projector, but can sometimes be found on the top or sides.
This cover is usually secured by two screws; undo these screws and lift the plate off to reveal the bottom of the plastic housing (the module) that holds the projector lamp in place in your projector.
This plastic housing usually has a handle attached to it. Pull gently on this handle to remove the projector lamp from your projector.
It is time to replace the lamp when:
* Picture has become dull and lacks brightness.
* There is an obvious decline in picture clarity and sharpness.
* Your lamp is flickering.
* There is difficulty or a delay when turning the machine on.
* A light comes on that warns you that it may be time to change your lamp.
Note:
1. Let the lamp cool down before replacing it.
If the lamp breaks, handle the shards
carefully to avoid injury.
2. Do not touch the glass portion of
the lamp assembly. Touching the glass
could result in premature lamp failure.
3. Be sure to seat the lamp fully and
secure the lamp cover. If the lamp is
not properly installed or the cover
is loose, the lamp will not turn on.
Customer
Reviewed in the United States on June 5, 2023
The XIM P-VIP 240/0.8 E20.9n from seller only lasts about 1/4 to 1/3 as long as a stock bulb. Bought a 2nd one since the price was cheap and had to return since it didn't even light up. Ended up going with a stock bulb from ebay.
Darren Thompson
Reviewed in the United States on March 24, 2022
Item installed just fine. Out of the gate, it worked just fine. It's in a projector in our basement so it's not used very often. This morning, after I would say less than 200 working hours, the bulb exploded, smoke came from the projector and set-off my smoke detector for ~ 5 minutes. Very disappointing. I guess you get what you pay for sometimes. The price SEEMED right.....
Customer
Reviewed in the United States on February 14, 2022
When new it took a long time to warm up and wasn't really better than the OEM after thousands of hours. Now after 360h the bulb is so dim it needs replacing.
b
Reviewed in Canada on March 1, 2020
Lasted for just under 3700 hours, as good as the original, very pleased.
737simnut
Reviewed in the United States on January 31, 2020
So far so good... The installation was easy and the display is good.
Beti Wilkins
Reviewed in the United States on July 22, 2019
It's great price and it fits perfectly in our projector and works perfectly
David Bourget
Reviewed in Canada on January 4, 2019
Lamp exploded in projector after 4 months of use. Really disapointed!
Rejjie
Reviewed in Canada on April 13, 2019
Have had for over 8 months. So far so good. Good brightness and lasting so far.
Spetznaz
Reviewed in Canada on September 24, 2018
About the same intensity light. I purchased 2. the first lasted an equivalent 425 Hours and the second lasted an equivalent 1325 hours.Very inconsistent lifespan. but it's also less than a fifth of the price of new. I'll look for alternatives before reordering this one again.
Brian
Reviewed in Canada on January 5, 2018
Just as bright as the OEM but at a fraction of the cost.So far I've logged ~300hrs.Time will tell if it can match the OEM which ran just under 2,000hrs
Recommended Products