Your cart is empty.
Your cart is empty. Features
▪ The mount has 4 locking positions which could locks the motor securely in place and fits nearly any outboard motor (refer to the model number of HP rating and capacity);
▪ Each mount has 10.5" of vertical lift fits both short shaft and long shaft outboard motors;
▪ Fits most style of 2-stroke outboard motors; not recommended for 4-Stroke motors.
Specifications
▪ Motor Pad Size : 10-1/4"(tall) x 8"(wide) x 1/16"(thickness)
▪ Vertical Lift : 10.5"
▪ Mounting Bracket Size : 5-3/4" wide by 4-3/8"
▪ Weight Capacity: 110 lbs
Note
▪ Manual measurement, error 1-3cm, depending on the actual situation, please understand;
▪ Please be careful of the sharp edge when you install;
▪ If not 100% completely satisfied with our item, simply contact us to request a refund or exchange. 3 month money back/replacement guarantee, 24 months product defect free replacement warranty.
Sproutylad
Reviewed in the United Kingdom on June 21, 2024
Bracket is expected works like it should
Customer
Reviewed in Canada on May 15, 2024
bateau,
steve
Reviewed in Canada on May 14, 2024
Not a good product.
IPM
Reviewed in the United States on December 25, 2023
Must remove handle to fit as handle will NOT clear transom. Instructions are NOT for this product. Instructions do have some useful suggestions; but follow them verbatim with peril. For price quality of materials are good. 1) remove handle and spring (spring material not gonna last with that range of stretch). 2) use rope and two pullies to raise/lower. There's a lot of these identical mounts for sale. Perhaps some garage factory in China has some parts and including printed instructions from other stuff and tossed these together and offered up cheap?
Dwayne Stephens
Reviewed in the United States on March 31, 2021
Not near as sturdy as they said. I made a couple of modifications and made it work
Donald Udell
Reviewed in Canada on December 28, 2021
I find not easy to tilt motor up and downHave to Titan wing nuts up too tight so they don’t come loose and difficult to loosen them off at back of boat
Ronald H.
Reviewed in the United States on June 9, 2020
The bracket is listed as capable of a use with a 25hp motor, up to 110 lbs. When I installed my 54 lb 4hp Yamaha the spring provided NO Lift support and the motor dropped all the way to the brackets lower limit. Lifting motor back up required excessive effort. After a single lowering and raising of the motor, the single spring had permanently stretched (without any load) about 1", providing even less lifting force. The bracket had excessive side movement due to the installation of all-thread bolts at the four bracket pivot points. The all-thread bolts would eventually damage to the bracket pivot points and the movement would increase. In doing additional research I identified other buyers of this bracket (different seller) had experienced failure of the exact same plastic motor support plate, used on my bracket, "breaking in two and the motor falling off into the water".YAE Marine (seller) contacted the manufacturer, but were unable to get any support from them. Since I had already drilled four holes in my boat's transom matching this bracket, so I decided to fix it instead of returning.FIX: I replaced the four all-thread pivot point bolts with 5/16" bolts that had smooth shanks and only threads at the very end (good fit). I replaced the single spring with three new springs, one 5-1/2" and two 3-1/8" (added a 1/4" bolt to existing bracket hole to attach back end of springs) side by side, below 5-1/2" spring. Lifting force is now adequate to raise motor with reasonable effort. The plastic motor plate is now reinforced with an aluminum plate and two steel mending strips bolted to the plastic plate (at the top and bottom) and trans-versing the weak point at the upper plastic plate holes used for mounting bolts (where the plastic motor plate broke in two) to the steel bracket. The attached pictures depict the new springs and reinforced plastic motor plate. New parts cost a additional $20 at Lowes, but now bracket is usable.BUYER BEWARE! DON'T BUY THIS BRACKET UNLESS YOU ARE INSTALLING A VERY LIGHT MOTOR OR ARE PREPARED TO UP-GRADE IT AS I DID. BUY A BETTER BRACKET!
Jerry Stumbaugh
Reviewed in the United States on February 15, 2020
Easy to install, and operates well
kr
Reviewed in the United States on September 4, 2019
I needed a new mount right at the start of fishing season and this one was less than half the price in a local store. It works great and was easy to install without having to buy any extra hardware.
Jeremy Lee
Reviewed in the United States on September 12, 2019
I bought this so that I can mount my transom mount trolling motor to the rear of my boat. It is very sturdy and well made. Very easy to mount and works well for my needs.
dean
Reviewed in the United States on September 12, 2019
Perfect fit
jason
Reviewed in the United States on September 11, 2019
I added this to my boat to use a 9.9 hp motor for trolling.it was easy to mount and is very sturdy.havent had any issues with the weight of the motor bending or destroying the bracket.its well worth the price for the peace of mind
Recommended Products
