Your cart is empty.
Your cart is empty. HOW TO WIRE IT:
red to + output(battery +)
green to ground ie - (Minus)
the other 2 wires, yellow and pink, AC input, connect to magneto coil
Specifications:
Voltage: Fit 12V Battery
AC Input Voltage: 20-60V
Unloading Output Voltage(Idling): 12.5~13v±0.5v
Charging Output Current: 0 - 4A
With Battery Charging Voltage: 14~14.5±0.5V
Working Temperature: -20°to 60°
Pedro Moneda-Avila
Reviewed in the United States on February 25, 2025
Purchased on Jan 1, and so far so good up to end of February.The housing didn't fit my Bintelli Breeze, but I simply cut, stripped, and crimped terminals into it for it to fit.It was relatively easy to install with the right tools, but it would be super easy if the housing fits. Just a click.Functionality: It charges my battery at a steady 14-15 volts and powers my headlight properly. It served my purpose. I tested with a multimeter while on and running.I am very happy with the price and value for money I get. It is an affordable part to find on Amazon. I live in Hawaii, and it's pretty expensive out here. Shops like to overprice things.
Malloryja
Reviewed in the United States on September 4, 2024
Good performance, worked as needed, durable.
Nathan Campbell
Reviewed in the United States on January 2, 2024
After burning up two Baja designs regulator rectifiers, I decided to try this much cheaper alternative. The Baja designs product kept burning up if I were at too high of an RPM for sustained periods. This one didn't give any trouble at all on the last two rides with me abusing the crap out of the bike. It also has a nice feature that the Baja designs did not. This one will charge a completely dead battery. The other one would not produce more than 6 volts unless the battery was above 10 volts starting out. My lights are all LED and all stay perfectly stable at idle or at a rev.
John R Ramirez
Reviewed in the United States on June 16, 2023
Easy to install and right fit.
alex rudy
Reviewed in the United States on November 26, 2022
Pushing 4a all day to run LED lights and an oil cooler. Works great. Gets warm but not too hot.
Joshua P.
Reviewed in the United States on May 8, 2021
I tried using this on an Apollo rfz once I installed a 5 wire stator on it so I could run a light bar on the bike but I could only get 3v out of the rectifier and I know the stator is good because I'm pushing a sold 12v from it so I am assuming it's the rectifier.
John Michalak
Reviewed in the United States on May 28, 2021
TBR7 replacement. Not an exact fit. Mounting holes don't line up. Used the mounting bolt in the top hole and used a thin tie wrap through the bottom hole. Battery is charging again. 6 pin connector, 4 wires, connector fit perfect and wires were a proper match. I would buy again at this price.
Sonic
Reviewed in the United States on March 10, 2021
Holds at 14 volts and the Description was one of the only that adds wiring info. Thank you! I copied it belowDescriptionHOW TO WIRE IT:red to + output(battery +)green to ground ie - (Minus)the other 2 wires, yellow and pink, AC input, connect to magneto coilSpecifications:Voltage: Fit 12V BatteryAC Input Voltage: 20-60VUnloading Output Voltage(Idling): 12.5~13v±0.5vCharging Output Current: 0 - 4AWith Battery Charging Voltage: 14~14.5±0.5VWorking Temperature: -20°to 60°
Recommended Products
$25.99
$ 10 .99 $10.99
$10.98
$ 5 .99 $5.99