Your cart is empty.
Your cart is empty.Product Description
Olena
Reviewed in Poland on February 7, 2025
Bardzo dobra jakość druku
Customer
Reviewed in the United States on September 22, 2024
Great prints after minimum setup. Easy to follow setup instructions and ready to print once you loaded the supplied sample filament.
David Z.
Reviewed in Mexico on September 2, 2024
Horrible trabajar con esta maquina, la tapa estorba y el uso termina por rayar la tapa ya que rosa con el cabezal que imprime, tienen un sistema extrusión malísimo los engranes deforman el filamento haciendo que se haga grueso en algún punto promoviendo que quede atorado en los engranes, dado que la tensión provocada por el tubo mal colocado genera una serie de problemas que impiden sobre todo hacer impresiones grandes, de verdad quería tener esta maquina pero es un dolor de ganadas de principio a fin
Victoria
Reviewed in the United States on May 2, 2024
This is what the original K1 should have been. Everything wrong with that printer has been addressed here.There is no need to pay for Bambu's overpriced hardware and closed ecosystem, this printer is half the price and just as good. No joke, I have run PLA, PC, PETG-CF, and ABS through the machine and it eats them all up.Great device. Very satisfied.
TimberrockRanch
Reviewed in the United States on March 15, 2024
This is my first venture into the world of 3D printing and I couldn't be happier. The machine is solid and prints flawlessly, so far. I have printed about a dozen designs from 12 minute to nearly 5 hour print times with no problems. Using only Creality Ender PLA filament at this time. My designs were created with the online TINKERCAD program and the provided Creality Print slicer. I haven't used any Cloud designs. I am amazed with the technology in the software/firmware and the precision of the prints. My only complaint is the Creality Store instructions/documentation. Lots of pictures, but light on verbiage. Same with their included product video. Some functions are intuitive, others not so much. Since this printer is pretty new, there isn't much on the Creality website. However, there is plenty for the K1 printer which is apparently nearly identical, so just browsing and I've found most of what I need. Time to make another print!
Doctor Wizard
Reviewed in the United States on December 27, 2024
I shopped long and hard before buying this printer. I've had a simple old Ender 3 for several years and got tired of fiddling with it. Don't regret the experience with the Ender cuz I learned A LOT. But now that I understand the process, I wanted a printer that "just works" and this fit the bill. I've had it for 2 months and it has been going non-stop with great results. Well, other than the screws that came loose from the bottom of the heatsink causing it to scratch my bed. I carefully looked at every brand and model of printer in this size and price range and was leaning hard towards the Bambu Labs which I think is the king of "just works" and still the one I would recommend to most people. But the deciding factor for me for this one is the open source firmware which can be upgraded to the full version of Klipper without voiding the warranty. (And it's cheaper with comparable specs.) That however would not matter for most people but if it matters to you, then this is the printer to get. If you could care less about open source, then get a Bambu or perhaps FlashForge Adventurer.
Stewie
Reviewed in the United States on November 22, 2024
I'm going to save you a TON of frustration. If you are in a country that uses 120V you will need to switch the power supply from 240 to 120v. The switch is located on the left side of the machine all the way at the bottom. It is a small square hole and you can see the switch if the shine a flashlight inside. Just use the supplied screwdriver and you are good to go. I did not see anywhere in the instructions to do this step nor did customer support mention anything about it.When I got the printer I followed step by step in the instructions. Going through the initial self test and the printer kept restarting at the hot bed step. My first thought was a power supply issue. So I looked everywhere for a switch or panel with any sort of markings and in the instruction manual; Nothing. I finally asked ChatGPT and it said this particular model had and auto sensing power supply and did not need to be switched. I looked for what felt like an eternity to find an actual phone number for support instead of just an email. So I called in. Worst English I could possibly imagine. I explained the issue and instead of her telling me to check the switch she said I need to email customer support since she didn't know how to help. So I emailed in. And again, instead of just telling me to check the power supply switch that it does in fact have, they wanted me to do a list of things before they would even attempt to help. Photo of serial number, original purchase receipt, video of the issue happening, and list of steps I've tried to fix it. So I just sent it back thinking I got a bad one and not wanting to deal with less than helpful customer support. New printer did the same thing. So after doing my own research I found a YouTube video of a guy that went through the same thing I did. Super easy fix. You would think that 1. they would put that very necessary thing in the instructions and 2. That the tech support line/email should just tell you about checking that switch first thing before going through all the other bull#@$&. Very disappointing start. I am not looking forward to figuring out an actual issue.As far as the actual printer goes its plug and play. I did not have to mess with settings much at all. Creality filament works great without doing anything which is great. Other filament types I found require a hotter nozzle temp than they have programmed in.
john a medina
Reviewed in the United States on November 10, 2024
It's a great printer out of the box, I'm sure if I play with the features more it could be even better. But as is, great printer.
Mercyman
Reviewed in the United States on October 30, 2024
It’s very particular about its files. Doesn’t like other software besides creality brands. Still working out the bugs. Great learning experience
Deus Vult
Reviewed in the United States on October 12, 2024
Try again, Creality.
Goncalves Carlos
Reviewed in France on October 1, 2024
A voir à la l’usage. Pour l’instant rien à redire
Recommended Products
$576.99
$ 99 .00 $99.00