Shopping Cart

Your cart is empty.

Your cart is empty.

4WD Auto Locking Hub for 1999-2004 Ford F250 F350 F450 F550 2001-2002 Ford Expedition 2000-2005 Ford Excursion 2001-2002 Lincoln Navigator Replace# 600-203, 1C3Z-3B396-CB

Free shipping on orders over $29.99

$28.99

$ 14 .99 $14.99

In Stock

About this item

  • [INTRODUCE] Even in 2WD, turning front wheels make the front axle spin, which can generate extra load on the engine and extra wear on the front differential. Hub locks allow the wheels to be disengaged from the axle when not using 4WD, letting them rotate freely. This saves fuel, extends the lifespan of drivetrain components and offers a smoother ride.
  • [FUNCTION] The 4WD actuator controls the power transmitted from the axle assembly to the front wheels. As long as the transfer case remains in the four-wheel drive state, the hub will remain in the locked position. When the driver switches to two-wheel drive, the clutch mechanism in the hub slides out and releases the hub, allowing the wheels to rotate independently of the axle.
  • [ADVANTAGE] The main advantage of being able to disengage the front wheels on the go is that the driver doesn’t have to stop, get out of his vehicle and twist a dial on the hub to disengage or engage the front wheels. The automatic locking hub does it automatically on the fly. The locking mechanism inside an automatic locking hub is sort of like a one-way clutch. When torque is applied by the driveshaft, it forces the hub to slide in and lock.
  • [REPLACE PART NUMBER] 600-203, 1C3Z-3B396-CB.
  • [COMPATIBLE WITH] Fit for 1999-2004 Ford F250 F350 F450 F550, for 2001-2002 Ford Expedition, for 2000-2005 Ford Excursion, for 2001-2002 Lincoln Navigator.


Fit the Following Vehicles:
Compatible with 1999-2004 Ford F250
Compatible with 1999-2004 Ford F350
Compatible with 1999-2004 Ford F450
Compatible with 1999-2004 Ford F550
Compatible with 2001-2002 Ford Expedition
Compatible with 2000-2005 Ford Excursion
Compatible with 2001-2002 Lincoln Navigator
Replace Part Number:
600-203, 1C3Z-3B396-CB
Easy Replacement:
1. Take off hubcap if your truck is equipped with large flat blade screwdriver or prybar. No need to remove wheel.
2. Pull out the retaining ring.
3. Firmly grasp the lockout portion of the hub, wiggle up and down while pulling away from the vehicle.
4. Install proper new locking hub in reverse order of previous steps.
Notice:
Please properly verify the Year/Make/Model of your vehicles before purchasing this product.
Welcome to contact us for any questions and we would response you ASAP.


Juan h.
Reviewed in Mexico on July 29, 2024
En la descripción dice que vienen dos cubos de Blockeo 4x4 y en la caja solo venía uno
Nicholas m.
Reviewed in the United States on June 8, 2024
No problem easy install.
Jesus Santos
Reviewed in the United States on March 11, 2024
Exelente producto, se lo intale a mi ford excursion y quedo igual que el de fabrica , lo recomiendo altamente.
Daniel A. Rickard
Reviewed in the United States on December 4, 2024
Worked as required
Zezhile Hansen
Reviewed in the United States on October 23, 2024
This was the style for my excursion but the holding rings were not the right shape. I just ended up using the old ones.
Sam Knighten
Reviewed in the United States on June 8, 2023
Works
Uncle Mo
Reviewed in the United States on June 30, 2023
Seems to be as good as OEM, solid, smooth motion, does have some polymer but so did the factory Ford one that went bad, replaced both sides in less than 20 minutes
Honest Abe
Reviewed in the United States on October 20, 2023
As expected
Doyle Barnett
Reviewed in the United States on January 23, 2023
The plastic piece that you turn to lock in the hubs was broken. Not in shipping. It was put together broke. Piece of junk
Recommended Products