Your cart is empty.
Your cart is empty.Product Description
Garage door bottom weather seal 16 Feet T-Ends
This is a T Type seal Designed to fit into a T track,Fits Most Garage Doors That Use a 1/4" or a 5/16" 'T' Channel Retainer.
Precautions
Before installing this part.You must make sure the T portion of the old seal is the same dimension of the seal Length is 2” MINIMUM Longer than size ordered and easily cut to any length to fit the desired size of the garage door.
Wayne Lubeski
Reviewed in the United States on March 18, 2025
THE PRODUCT WORKS WELL, AS PRESENTED, WENT INTO TRACK PERFECT.WILL BUY AGAIN.
Yangming Wu
Reviewed in Canada on February 17, 2025
Looks this product is good. But the thickness is only about 1 mm. That means it is very soft and not good for the bottom seal.
ZMANZ
Reviewed in the United States on July 8, 2024
THIS ITEM ACTUALLY DOES HAVE 5/16 T's. HARDER TO INSTALL BUT DOES NOT POP OUT OF THE TRACK. MATCHED UP EXACTLY TO MY OLD SEAL.
Perkinstown
Reviewed in the United States on July 24, 2024
A great replacement for the old weather seal. Easy to install. Plyable. And sealed the garage door.A good value for the money.
Scott
Reviewed in the United States on June 2, 2024
Exactly as described. Ordered longer than needed. Was a little difficult to get both end to slide in at the same time. Best advice is to clean tracks a keep lubed.
Bill Monaghan
Reviewed in Canada on June 2, 2024
Received product on schedule. Read reviews of install issues. They are kinda correct. So here is my hack that made this a breeze to install. I have a 16 foot door. Take the old seal and mount right off of the door. 2 screws each side where the bottom roller attaches and however many screws are holding it to the door. Lay channel on ground. Take a scratch awl and tap into both the ends where the channel is pinched to hold seal in. Remove old seal. A little brush to clean channel. Run 1 side of seal completely end to end. The other side start at one end and use a screen spline tool to push the rubber seal into the channel. I was amazed how quick and easy this work. Took like 20 minutes.
Mike Reed
Reviewed in the United States on May 29, 2024
The round part of the seal was smaller than original but it slid in easily with 2 people. I used soapy water and cleaned the track prior to installing. I used a paint brush to clean the track. It was plenty long enough for my double car garage. I used a pair of scissors to cut the excess off both sides.The quality is a little less thick than the original but it seems to work. Will update in the future if problems occur.
Gigger Famador
Reviewed in Canada on November 8, 2024
Perfect fit! Easy to install! I had mine exchanged with the help of my wife.
Christma
Reviewed in the United States on November 7, 2024
easy to work with great price & good quality.
Kevin G
Reviewed in Canada on November 18, 2024
Did as needed
Debra Jones
Reviewed in Canada on November 12, 2024
Was easy to install need 2 people and just slide it through looks great
Gar
Reviewed in the United States on November 16, 2023
Replaced our old worn out seals on the Wayne Dalton 24 year old shop doors. Had tried last week to get a different type seal that had the extra round rubber in the center…needless to say, the doors would come close to closing.Replaced with the seals that arrived today. Using my wife as a helper applying soap, the seals both went on in about 10 minutes each side!Made a very air tight seal with no light shining through on the bottom of the doors. Forced the doors down tight to close and will leave closed for couple of days while the seal stays in place.As in other reviews, apply soap as you push the seal into the grooves!
Robert Gillard
Reviewed in the United States on October 27, 2023
Very easy to install. Took longer to remove the old weather seal. Once old one was removed I cleaned track and sprayed with wd40 for easy installation.
Recommended Products
$16.50
$ 6 .99 $6.99