Your cart is empty.
Your cart is empty. 835257Q1 Flo-Torq II Hub Kit - for Mercury/Mariner and MerCruiser Engines
Perfect replacement for Flo-Torq II hub system for outboard and sterndrive engines,Replaces OEM#:835257Q1
For use with MerCruiser Alpha, Alpha One & Bravo One (under 400hp)
NOT FOR Mercury/Mariner 1977 and older.Not compatible with Verado V8 engines with 1.25" prop shafts.
Fit for 13 1/4*17 and 14 1/2*19 propellers For Mercury interchangeable boat propellers that accept Flo-torq II.
Compatible with:Mariner 40-60 HP Command Thrust,70-250 HP, Force 90-120Verado 150-300 six-cylinder with 1" shaft only.
Mercury / Mariner 75HP:1984-Newer
Mercury / Mariner 90HP/115HP:1978-Newer
Mercury / Mariner 125HP:1994-Newer
MerCruiser 120-260HP:1983-1985
Verado 150-300 HP
Force 75HP:1999-Newer
Force 90 /120 /150HP:1995-Newer
Alpha one Drive(Gen.1&Gen.2 ALL Motors&HP)
Bravo one Drive(Bravo one & Bravo one X Drives ONLY)
The mercury flo torq 2 hub kit perfect fit for boat Propeller to provide a pleasant boat trip.
Our prop hub kit can be installed on-site and used directly,saving time on water waiting for replacement rubber hub.Make sure a quick and simple repaired at the same time.
When the plastic sleeve is cracks or damaged,boat is having difficulty planing or feel a vibration in your propeller,it needs to replace the mercury 835257q1 flo-torq ii hub kit to make your boat runs efficiently and better.
The propeller hub kit for mercury outboard reduce drivetrain noise&vibrations to protect propeller&drivetrain from impacts,provide lower fuel consumption and great speed acceleration or rmps,reduce the wear and tear on engine,improve boat performance.
Super easy and convenient to install:Just remove prop locknut&locknut retainer& forward thrust washer.Then Install forward thrust washer---Insert drive sleeve into prop---Slide prop on prop shaft---Insert drive sleeve adapter--Slide locknut retainer---Install prop locknut---Insert sth to prevent spinning--Tighten prop locknut.Pls be sure to apply grease on the spindle when reinstalling the boat trailer hub kit.
Victor
Reviewed in the United States on January 14, 2025
It works great
Lyndsie
Reviewed in the United States on August 3, 2024
These are good kits. They look and work just like the original manufacturer and I found them just when I needed them. Great as a replacement part or to keep on hand in case your prop gets damaged.
STEVEN E.
Reviewed in the United States on August 22, 2024
This unit is made to allow quick easy propeller changes for your boat. It also helps absorb shock to the propeller protecting your lower drive units. The Flo-Torque adapter units fit different models of drives allowing propellers to be used across different models. This r can really save money on boat maintenance. This unit is a quality product and allows interchange of general purpose propellers for a quiet day at the lake or a high performance propeller for wake boarding and water skiing. A word of advice- be sure to remove the adapter and grease the drive shaft and adapter to prevent seizure. Believe me, this is not a nice occurrence. The easy propeller change along with protection of the propeller and drive components due to the shock absorbing properties results in high performance of this unit. I think you will be pleased with this purchase.
Jim Hewitt
Reviewed in the United States on June 8, 2024
I got this hub converter kit for a new prop I’m trying out on the boat. The hub has three purposes:*Convert from prop hub to boat/motor prop shaft size and spline count*Soften the shift clunk*Provide relative isolation between prop and gearboxThis hub will fit any prop that is designed for the Flo-Torq II. The black plastic/rubber insert was a little tight going into my new prop. I used a hammer and block of wood to drive it carefully home. I will have to do the same should I ever try to remove it.While it is difficult to compare directly, but it SEEMS like the shift clunk is reduced compared to the previous prop/hub. This is an unexpected benefit for me.The last item – protecting the gear box against prop strikes – is difficult to test. That would be a ‘destructive test’. But you can see from the black plastic/rubber that it should spin if the prop gets stopped abruptly, I just couldn’t compare it to see how well it does that.So, as far as I can tell, this hub kit does its job. It does it for a good price $37 at the time of this review. In fact, the price is good enough for me to pick up another to keep onboard as a spare.
Lewis Walker
Reviewed in the United States on December 19, 2024
I expected to have a quality flow torque hub. This was an inexpensive China hub and the brass splines were stuck in the plastic. I had to hammer it out. Shipping was great, price I though was great until received.
Picture Pefect
Reviewed in the United States on November 11, 2024
It was easy to use and worked perfectly.
Clarissa 'Selah Range Co. LLC'
Reviewed in the United States on October 23, 2024
Good quality
Recommended Products
$54.99
$ 23 .99 $23.99