Your cart is empty.
Your cart is empty.Product Description
Advanced DYNARMOR Technology
No Fiberglass, No Worries
Traditional cut-resistant gloves achieve high levels of protection by using fiberglass along with steel wire or high-strength yarns such as aramid or UHMW-polyethylene. However, OSHA treats fiberglass as a nuisance dust.
With our innovative Dynarmor technology, we have achieved all high levels of cut-resistance without using fiberglass. This means you can enjoy the highest protection levels without worrying about exposure to potentially harmful fiberglass dust.
Durability and Long Life
The reinforced stitching and durable materials ensure that they withstand heavy use without tearing or wearing out quickly.
Superior Dexterity
The snug fit ensures you can handle small objects and perform delicate tasks with ease, unlike bulkier gloves that can hinder movement.
Comfort for Extended Use
Our gloves feature a breathable design that prevents sweating and discomfort, allowing you to work longer without irritation and reduces hand fatigue
Machine Wash
Clean sharp residues before washing.
Machine wash cold in gentle cycle.
Do not tumble dry. Air dry for longer lifespan.
rover
Reviewed in the United States on September 27, 2024
The A9 cut resistant gloves are woven from high performance polyethylene fortified with tungsten. The palms have a grippy nitrile coating which is water and oil resistant. All fingers and thumb, front and back, are touch screen compatible. That is an improvement over other gloves I have that only have forefinger compatibility. The sleeve extends 2-inches back from the wrist. (Medium glove size).To test the gloves, I drew a sharp knife across the back of the gloves and at the palm. The knife didn't penetrate or leave marks on the glove. The gloves are not puncture proof, however. I was able to poke a paper clip through the back of the glove using a bit of force. I wasn't brave enough to test them with a chainsaw, but I am satisfied that under normal use they will protect my hands.I ordered a medium size based on the Sellers size chart and the fingers could be longer. Also, I found the cuffs to be a bit loose. The material could have more stretch around the wrist. Bottom line though, these are good gloves with good features and a high degree of safety built in.
X nemesis X
Reviewed in the United States on September 21, 2024
Decided to give a pair of these a try when found and made for a wise choice. Always can use a good pair of gloves when it comes to heavy yard work and these do the intended job just fine. Spent an 8 hr day with em on most of that time transplantin some bushes and wackin back a variety of other bushes n' plasnts due to the comin winter season which'll b here soooon enuff. Also have an array of hedge work to accomplish for which I already started - again another 6 hr day with em on for that duration - and I'm talkin 100ft sets of 4ft tall (when in trim) hedges where some r 4-5 ft in depth due to em being double-thick. First set completed the other day with these on ... again NO flaws found - threw em in the wash - removed from dryer after a short 5 min of the whole cycle for the rest of the contents - came out practically as when brandy new other than havin some slight fade wear in the protective black palm n finger areas - noting they ran thru some pretty mean brush along with all the hand work of rakin afterwards plus the other days work mentioned.Personally chose a 'Large'. These measure out un-stretched at an approx 9 3/4" full length (tip of mid finger to end of cuff). Mid-finger length is approx 3 1/4" to webbing and hava 3 1/4" laid flat width of cuff. Cuff length itself b a nominal 3" which is a tad more than found in cheaper made varieties. They do fit quite well thou a tad tight - but they breathe well since noted they were adornin the hands for some odd hours at times in 70-80 degree heat without issues - thou tad harder to remove n hands needed a few minutes to rejuvenate back to norm - so do feel the sizing runs a tad smaller to others in my lifetime chosen in the large size - personally 5'10 at 150 so if yur larger - defintely advise to opt for a larger version.Have 3 more sets of the 100 footers to wack back nice n strait so IF they happen to fail for any reason during or afterwards can get back on here to edit the scribbles and add the when, why, and outcome.For the price point asked for when considering overall fitment, performance, and wear characteristics - can state this products a great value in the current bidenflationary times ... ' 👍 '
Jon
Reviewed in the United States on December 20, 2024
I gave it 4 stars because of the price. I guess you get what you pay for. Good product.
David Raiman
Reviewed in the United States on November 9, 2024
The first pair I got seemed too thin to last but these are great for good tactile feel and yet protect my hands very well.
Dawn
Reviewed in the United States on November 26, 2024
I handle metal all day I guess we will see how many days they last
Road Warrior
Reviewed in the United States on November 25, 2024
The media could not be loaded.
Recommended Products