Your cart is empty.
Your cart is empty.Product Description
Installation Steps
Installation first step
1. Remove the original shifter gears knob.
2. Remove the aluminum alloy cover from the bottom of the original gear shifter head
Installation second step
3. Match the size of your shift stick from one of 3 black rubber adapters, and install on the gear stick.
Installation third step
4. Put into the aluminum alloy bottom cover of the new gear knob into the shift stick rod.
5. After placing the aluminum alloy cover on the rod, put the shifter handle knob on the rod.
Installation fourth step
6. Small screws tightening, finally, tightening the aluminum alloy cover
5 Speed Shift Knob
Adapters size chart
3pcs different plastic adapters of shift gear knob inner diameter are 0.31inch, 0.39inch, 0.47inch (8mm,10mm,12mm), available for your choice
- Attention: If the three screw sizes are not suitable for your car, I suggest that you can use tape wrapping on your gear stick and then tighten it to solve this problem.
Product parameters and information
Specification:
1.Product name: Gear Shifter Knob
2.Material: Aluminum Alloy & PU Leather
3.Color: Black
4.Product size chart Length is 3.49inch (88.65mm) wide is 2.13inch (54.1mm)
5.Due to manual measurement, please allow an error of 0.1-0.2inch, thank you for your understanding
- Attention: 1. If your MANUAL car reverse gear needs to be lifted, then it can't be used
- Attention: 2. If your AUTOMATIC car reverse gear needs button lock, then it can't be used
- Attention: 3. If your original manual gear knob can't be removed, then it can't be used.
- Attention: 4. Before buying, please make sure that the size of the adapter is suitable for your car gear stick size.
Cheryl Fite
Reviewed in the United States on February 25, 2025
This was easy to screw right on the handle. It looks nice. It fits great.
Tyler Schliecher
Reviewed in the United States on February 21, 2025
Overall I like it. It does make my stick shift feel a tad longer. So there might be a slight adjustment on my shifting. There are no instructions with the product but it's not difficult to put on. Slide the threaded locking ring on the stick first. Place the knob with the appropriate sized plastic piece, inside the knob. Screw it on the stick and then secure it in place with the mini screws provided and then screw on the bottom ring. We'll see how well it holds up after a few drives but it appears to be durable
Russhel l lillo
Reviewed in the United States on February 16, 2025
Exactly what I needed
Mrhappy
Reviewed in the United States on January 11, 2025
Arrived with two allen screw holes either stripped or not threaded. One allen screw is stuck to the allen wrench. Cover that goes over allen screws wouldn't fit over allen screws before I even tried to install it. Worst experience online I have ever had. Junk! UPDATE: The seller sent me a replacement at no cost to me, only to have the same issues as before. Nothing was fixed, adjusted or change. It is exactly the same as the first one.
JimM
Reviewed in the United States on August 20, 2024
Installation on my jeep Patriot was easy. I found the spacer provided a very snug fit and I had no problem with the screws. It's been three weeks since the installation and it's still secure. Overall I'm very happy with it.
Tyler Noll
Reviewed in the United States on July 18, 2024
It was easy to install, It looks great and works great. And I have no trouble with the stability or it's spinning around. The fastening system holds a very tightly. So good quality product. And would recommend.
Roteck
Reviewed in the United States on March 29, 2024
Do yourself a favor and grab their hex tool, throw it in the trash, get your own 2.5 hex tool and use that. You WILL strip the securing nuts with their tool. I could not get it tight enough without their tool slipping and stripping the crap out of the nuts until I grabbed my own tool then I could tighten it down to my heart's content. It feels high quality and looks good but I wish it was weighted. I've tried a ton of different shifter knobs from T handles to big 3" 2lbs spheres and this one just feels right...once you get it tight. I really don't understand why they can't thread it and have adapters like pretty much every other shifter knob I've tried. It's the only one that uses the 3 locking bolt things. I may thread it myself and use a weighted adapter or something. But other than that it's pretty cool.
Ken S
Reviewed in the United States on December 14, 2024
Nice looking product, I'm using it but it doesn't fit tightly !
Recommended Products