Your cart is empty.
Your cart is empty.From the manufacturer
This aluminum flush nailer is a high quality adjustable flush nailer. It can be attached to the nose of the nailer either by set screws (includes allen wrench) or thumb wing nuts.
The Flush Drive prevents nails from being over driven with the nail head below the material surface which can greatly reduce the holding strength of the fastener and lead to premature failures of the mechanical holding of the nail.
ACC-FD Big Foot Tools Flush Drive
Compatible with:
- Hitachi NR83A 3-1/4″ Full Head Nailer
- Hitachi NR83A2 Full Head Framing Nailer
- Hitachi NR83A2(S) Framing Nailer
- Porter Cable FR350A Round Head Framing Nailer
- SUPCO SFN-88 Framing Nailer
The Flush Drive is “C” shaped to ensure added protection for the operator of the nail gun. The “C” shaped design allows the nail to pass through the nail gun properly without the flush drive interfering.
Rus Cayde
Reviewed in the United States on October 16, 2024
Bought it to sheath my 1950's home with my framing nailer and it worked insanely well! Not a single overpenetration!
Customer 04040404
Reviewed in the United States on December 8, 2023
Bought this for a siding job that I had coming up ended up lossing it before the job so bought another one. This is great if you do not want to bury the nail in the siding of T1-11.It works as it should and keeps the nail flush or just under flush. It is easy to put on the end of your nailgun and easy to take off. Small enogh you can store it will nailgun or in your tool bags.
Ldt51
Reviewed in the United States on January 16, 2022
Easy to install for nails shorter than 3-1/4". Shot my 2-3/8" nails in flush.
DANNA, MICHAEL J.
Reviewed in the United States on September 5, 2021
I use this on my Metabo/Hitachi NR90AE(S1) framing nailer when installing siding. I mainly use it as an no-mar option instead of the little hard plastic/ synthetic rubber ones that you can buy specifically for this gun that wear out way too quickly & repeatedly blow off when they get worn. The thing is that you don't want to use the set screws to secure this flush drive nose piece on your framing gun if you also use it for framing. So the tip is to obviously use the thumb screws, but they have a tendency to loosen frequently. Put one, or two wraps of plumber's thread sealing tape on the threads of the thumb screws & trim off the excess. You'll have to reapply next time you use the gun for siding or after you take this off in order to use it again as a framer but there you have it. All that said, the flush drive nose piece adapter works great as an no-mar option for your framing gun or as an flush driver.
gcervantes9
Reviewed in the United States on March 8, 2021
Added this to one of my framing guns for siding installs, I used the allen screws vs the thumb screws, I won't remove this much but thumb screws great if you only have one gun. Much better/ duable than the rubber ones I see that come with the new framing nailers and all at a very reasonable price.
Ricardo trujillo
Reviewed in the United States on March 18, 2021
Fue útil para hacer el trabajo, buena herramienta para cuando no contamos con una pistola Hitachi de regulador.
Isaac H.
Reviewed in the United States on December 15, 2021
I used flush nailers for siding for years, back when Hitachi guns didn’t have the stupid built in flush nailers that truly suck and are virtually worthless.I still have my 20 year old Hitachi framing gun, no stupid guard around the spring, no spring either, which is how I’ve nailed siding and exterior trim for a long while. I bought this flush nailer to use for fence pickets. It is the same as my old ones but for the thumb screws, the old ones only had Alan screws to secure it to the push lever, which this one also has, but the thumb screws are quicker. The thumb screws might get in the way of you had to nail in a tight corner but other wise they’re a useful addition.Nails sank perfectly flush, the flush nailer didn’t fall off, it also seems durable.I’m satisfied
deano
Reviewed in the United States on October 27, 2020
I used this product on a Porter Cable framing nailer to limit the depth of set on the nails. I was able to get the nail heads flush with no over driving. I was very satisfied and happy to avoid buying a siding nailer for just one small project
Recommended Products
$29.99
$ 15 .99 $15.99