Your cart is empty.
Your cart is empty.【Features】:14.9 inches in length,1.45 inches diameter 【Specification】: - Material : Aluminum Alloy - Type : L shape with Flange - Unit Weight : 9.5Oz (270g) / pcs - Product dimensions : > Diameter of aluminum tube : 37/1.45 inch > length : 380mm/15 inch > Flange Width : 90mm/3.5 inch (dimeter) Quantity: 1 pcs - Colors : White 【Package Included】： Adbamic pole mount X 1pcs 【IMPORTANT NOTE】：Please contact us if any query, we will work with you to solve the problem.
Stephanie
Reviewed in the United States on July 26, 2024
Purchased this to mount my weather station to my patio and it worked perfectly. Fits the Ambient weather WS2000 mounting gear. Feels very solid and has held up well through several heavy Florida storms so far!
NJPE
Reviewed in the United States on February 7, 2024
Took me a little bit of search finding this great product. As you can see in the pictures very sturdy bracket, lightweight, painted, possibly rust-proof. It came with heavy duty screws. In my case, it made my weather station sender installation easy, because I could rotate for perfect south direction for accurate wind direction readings. I highly recommend for similar applications.
Andrew L.
Reviewed in the United States on February 19, 2024
Mounting hardware is junk, but pole is nice.Bit short.
Johnny J Sanchez
Reviewed in the United States on November 21, 2024
Work out great, very lite, like the cable holes on top and bottom. Perfect on side of the house. Product price perfect.
David
Reviewed in the United States on October 9, 2024
Perfect for my needs. Had my Starlink set up in minutes.
Gary Haydu
Reviewed in the United States on October 1, 2024
Nice looking mount for my outside antenna.
John Matus
Reviewed in Australia on August 5, 2023
It contains mounting screws. It has mounting slots to allow for some rotation so that you can get it in a perfect vertical positon.
B. Elmore
Reviewed in the United States on July 18, 2023
Decent construction, but its paint scratches off easily when I rotated my antenna (trying to find the best signal). I imagine that it will be far more susceptible to rust unless I go to hassle of repainting it. I wish I had gone with galvanized pipe instead.
Mary Torres
Reviewed in Mexico on December 1, 2023
Buen material
SteveV
Reviewed in the United States on September 25, 2022
I recently purchased a WeatherFlow Tempest weather station and needed a J Pole type mount to attach it to. The Tempest weather station only accepts a pole diameter from 1” to 1.315” which is considerably smaller than a typical J Pole type mount. This particular mount has an outer diameter of 1.45” also making it too large for the Tempest but it works brilliantly with a bit of surgery. I’m including the information here with the hope that it will be useful for others.1. 1” PVC pipe has an outer diameter of 1.315" which coincides perfectly with the inner diameter of this mount. However, the opening at the top of the mount is likely to be slightly deformed which will make it difficult if not impossible to slip the PVC pipe into the mount. Since I didn’t need the cable opening (or rubber grommet) in the mount, I used a power miter saw to cut off a couple of inches off top of the mount just below the bottom of the cable opening. The mount is made of aluminum and cuts well with a carbide blade. I placed a wrap of painters tape at the cut location, easily cut it with a power miter saw and cleaned up the cut edges with a bit of 220 grit sandpaper. With the small section of the mount cut off, the tube is nearly perfectly round and allows the PVC pipe to be inserted into the mount. Note that it’s a tight fit and you’ll need twist the PVC into the tube. I managed to insert it approx. 5” and it’s definitely not going anywhere.2. Before inserting the 1” PVC pipe into the mount, I painted it with some satin white spray paint, once the paint was dry, I applied a bit or exterior caulk to the joint where the PVC pipe mates to the mount.3. Since I’m not routing any cables through the mount, and since I didn’t want any openings in the mount to become a potential home for bees/wasps/hornets, I cut a 1.5” length of PVC pipe in half, applied some caulk to the outside edges and slipped it in the mounting flange end of the mount to cover and seal the opening.4. Lastly, I gave the entire assembly a couple of coats of satin white spray paint.
Recommended Products
