Your cart is empty.
Your cart is empty.Momentum Series Cold Air Intake Systems are designed and tested around the performance needs of gas truck and car applications. All Momentum Series Cold Air Intake Systems ensure maximum horsepower and torque with the largest filter possible. Each Momentum Series Cold Air Intake System is dyno-tested at our in-house dyno in Corona, CA. The Momentum Series Cold Air Intake Systems feature a one-piece sealed housing, filter-to-housing interface, premium hardware, and filter options of ProDryS, Pro5R, or ProGuard7 depending on your application and performance needs.
Dominque
Reviewed in the United States on February 20, 2025
You do notice a different but I think that when you do get this its better to have your vehicle tuned as you should afterwards for peak performance.
Kindle Customer
Reviewed in the United States on September 13, 2024
Great product at a Great price, was very easy to install. Most time was to install the grommet and plastic insert in the breather neck but looks fantastic and increased sound, can't say about increased mileage but if I can stay out of the throttle maybe I will see lol
Do-er64
Reviewed in the United States on August 20, 2024
Solid built. Fits right. Ez install. Love the look and sound. Didn't check for any better mpg. Not sure how difficult it would be to remove the filter for cleaning.
Tee
Reviewed in the United States on December 7, 2024
This intake made my Durango sound so good. Now to tune to get the power out of it.
Ian
Reviewed in the United States on April 6, 2024
Great product, easy install took less than 20 minutes. Fits the 2018 Durango r/t with the SRT hood. After reading other forms, it’s recommended to put some silicon around the clear window if you have the SRT hood to prevent water leaking in.
Jay
Reviewed in the United States on March 7, 2021
I wanted so much to love this intake. Yes I know it’s basically for sound.Bought it and it was trash. The tube at the end was bent it. Fine I can use a heat gun and fix that.After removing the stock box and trying to install the new housing after spending 10 minutes to try and get it to sit down I slide my hand under and discover one of the holes isn’t drilled in the right spot. No matter how it’s set either the single post closest to the engine slides in or I can get the 2 closer to the fender to mount.With all that and the fact mine is a 2020 bought it brand new I wasn’t going to deal with possible warranty arguments with my dealer AND of paid over $400 for an intake that fits like crap. So back to Amazon it will go. It’s a shame it’s a nice looking piece but paying to be aggravated ain’t worth it.
Jeff
Reviewed in the United States on May 21, 2020
I am writing this review to put your mind at rest about the SRT hood supposed issue in the deacription. It states it doesn't fit. Like many of you, I debated about ordering after reading this.Here is the answer you are looking for. I even asked AFE the question on this product in the questions below ... and they didn't answer. It was frustrating considering they responded to another question. This product absolutely fits all Durango models with the stock SRT hood. I have no idea why they stated it did not work. Fits perfectly. A few tips ... be careful with the sensor that you move to the new tube. It is tough to turn but it does turn. It doesn't turn but about a quarter turn. Dont force it past a quarter turn and pull it straight out gently. Next, take your time and make sure everything is tight. The clamps almost tighten all the way down on the tubes. Be gentle though and use a small driver so as not to over torque it. You want them tight so the tube doesnt slip off the filter housing. This is especially important where the filter sits in the housing itself.. this has to be tight or you run into the problems some of the other commenters ran into.. Overall, I felt like it made a huge difference on my 2020 RT ... especially in the higher RPMs. Hopefully this helps someone else on the fence about whether to order if you have an SRT hood. There is definitely some uncertainty with the description.
Chris
Reviewed in the United States on April 2, 2019
The condition that the box came in first off was distroyed! I should of sent it back at that point but I went against my better judgement and installed it anyway! Once I did the filter will not stay in the box no matter what I did it will move with the engine and eventually fall out of the box because the engine flexing pulls it out! The design of the tube needs to be different somehow to keep this from happening! Needless to say I’m not very happy with this expensive intake that does not fit right!
Recommended Products
