Your cart is empty.
Your cart is empty. ★Parameter
Inlet/Outlet Dia:1/2" MNPT
Volume:0.75 Liter(25 FL OZ)
Water psi:Max 125 PSI (8.6 BAR)
Pre-charge pressure:10 PSI(0.87 BAR)
Air Fill Vale:standard automotive style tire valve
Applications:Boat,Marine, RV,Caravan,ect
★Please Note
1.Relieve air psi prior to disassembly
2.Do not use to pump flammable fluids,gasoline,kerosene fuel oil
3.Do not use pump in a explosive environment or use where flammable vapors are present
4.Petrol or fluids with flash point below 37°C(98°F), explosion or death may occur.
5.The accumulator tank comes pre-pressurized at 10 PSI. For optimal usage, please set accumulator tank to ~3 PSI below your water pump's cut-in pressure and make sure it is connected to the outlet of the pump
6.Do not over pressurize tank. Pressures over 125PSI(8.6BAR) may rupture tank and cause personal injury.
Mario
Reviewed in Canada on September 6, 2024
Pour le peu de litre qu il y a sa vaut pas la peine
At1bob
Reviewed in the United States on March 31, 2024
works as it . would be easier to install if it included the fast connectors to the pump, which I had to order seperatly.
Sam G.
Reviewed in the United States on August 19, 2023
Smooth flow
Scott
Reviewed in the United States on July 8, 2022
Worked as described. Some noise reduction and less strain on pump.
Customer
Reviewed in the United States on July 25, 2021
My high pressure valve on my RV water heater (six gallon tank) dripped. This occurred at high temperature and a new valve did not correct the issue. The thermal expansion, blocked by the system check valves, was increasing the pressure in the system.Installed this. Charged it to incoming line pressure. The leak/drip has ended.Easy to install.Must be on the pressure (out side) of the pump.
The Goat
Reviewed in the United States on July 19, 2021
So this is on our boat. And that said, the boat was neglected before we bought it and I have spent a lot of time fixing what feels like everything and this was one of the first "mods" that I have done. The previous owners did not believe in filtering their water, I swear they used a bucket that had sand in it to fill the potable water...it just feels that way. So after cleaning out every part of the faucets (had to replace one of them) the pressure and volume was good --- but it pulses as the flow rates are low enough that the pump keeps up and cycles. I know how the system works and decided to put in a pressure tank. this one is small and lightweight -- made for an easy install. Once I gained access to the pump area, I cut into the line and was done in less than 2-min. Made a trial run and everything does run smoother.My goal was to make the pump cycle differently and prevent the ups and downs associated with an on demand pump system. Before it was installed the galley sink would noticeably pulse whether on full stream or sprayer. Now... it has a very slight pulse that you can see mainly because you can hear the pump at the same time. It does make the flow more even on either setting.Overall I would say I am happy with it and honestly they should install these from the factory when they built the boat.
Balboa
Reviewed in the United States on December 8, 2021
I bought this to stop the low volume rattle and hard stops if the pump. Vey easy install, works as advertised!
DaVid
Reviewed in the United States on April 16, 2021
Great to have in your RV system. It makes a difference in the water flow, just like advertised. So easy to install and all the parts work with the installation.
McMac
Reviewed in the United States on April 13, 2021
With the smaller size it's simple to find a spot for installation in space-challenged RVs. It works well, "softening" the pump run/noise and helps to maintain and "level" water pressure when utilizing the on-board water system in an RV.
Recommended Products
$2,325.00
$ 99 .00 $99.00