Your cart is empty.
Your cart is empty.Product Description
Compatible with Dual Plane Intake Manifold for Chevy 262-400 1955-1986 Small Block 2701
- [1]fits Chevy 65-68 1975 Bel Air // 1965 Biscayne // 1974 Blazer // 75-86 C20 C10 Suburban C10 // 1975 1977 1980 82-86 C20 Suburban // 65-73 C10 Pickup, 65-68 1972 C20 Pickup // 75-86 C30 // 67-68 C30 Pickup // 66-86 Camaro // 65-68 1974 76-78 1981 Corvette // 75-82 El Camino // 75-86 G10 G20 G30 // 65-72 74-85 Impala // 75-86 K10 K20, 1967 K10 Pickup, 75-86 K10 Suburban, 77-81 83-86 K20 Suburban, 77-86 K30 // 75-86 K5 Blazer // 75-81 Malibu // 74-86 Monte Carlo // 71-79 Nova
- [2]fits GMC 77-78 C15 // 1974 C15/C1500 Pickup // 79-86 C1500 // 85-86 C1500 Suburban // 75-78 C25 // 79-86 C2500 // 75-78 C35 // 79-86 C3500 // 1978 Caballero // 1978 G15 // 1979 85-86 G1500 // 79-86 G2500 // 76-78 G35 // 79-86 G3500 // 75-86 Jimmy // 75-78 K15 // 79-86 K1500 // 84-86 K1500 Suburban // 75-78 K25 // 79-86 K2500 // 1986 K2500 Suburban // 1978 K35 // 79-82 84-86 K3500 // 1977 Sprint
- [3]fits Buick 1979 Regal // 75-78 C15; [4]fits Olds 1978 1981 Cutlass // 1978 1982 Cutlass Supreme // 1977 Delta 88; ⑤fits Pontaic 78-79 Firebird // 75-76 Grand Prix // 1975 Grandville // 1975 1981 LeMans // 1985 Parisienne
- [Sepcifications]: Material Type: Aluminum
- RPM Range: Idle-5,500
- Intake Type: Dual Plane
- Carburetor Flange Type: 4-Barrel Square Bore
- Port Height: 1.85 & Overall Height: 4.25
- Bolt Hole Pattern: 5.160" x 5.625"
- Port Width: 1.15 & Mounted Height: 4.25
kjdcomp
Reviewed in the United States on July 30, 2024
Looks good fit was good and vehicle ran as it should.
Jean
Reviewed in the United States on May 9, 2024
We liked the part.
Customer
Reviewed in the United States on October 27, 2024
1985 p30 Chevy step van.Fits amazing. No issues. Would recommend to paint it before installing.
Riley blewett
Reviewed in the United States on January 12, 2024
It came damaged and idk if it’ll affect the installation or fitment yet.
SR
Reviewed in the United States on October 19, 2023
ok piece, looks good, but machined surfaces are off a bit, going to have to remove and sand surface in a couple of areas, leaking a small amount of water to the outside of head
Mike J.
Reviewed in Canada on October 10, 2023
After taking my time to make sure all surfaces were clean i then install the manifold. waited one full day before i added antifreeze only to have a leak between intake manifold and cylinder head. I have now removed the manifold and gaskets to yet clean and reinstall. I put a straight edge along the runner of the manifold and it is not straight, so mt question is do i return it and wait for another or take it to a machine shop and have it plained?
Recommended Products
$55.95
$ 25 .99 $25.99