Your cart is empty.
Your cart is empty.Product Description
Package include:
- 1× SDF20NK5X Servo Driver
- 1× 1.8KW 110F-0630NCL(A) AC Servo Motor without brake
- 1x DB25 hole plug and shell
- 1 x 3m Power Cable with Plug
- 1 x 3m Encoder Cable with Plug
- Pdf. user manual (If you have not received the user manual at Amazon Message Center from us,please message us)
- Model: 110F-0630NCL(A)
- Power: 1.8KW
- Number of poles: 5
- Rated power supply: 220V
- Rated current: 8.2A
- Net weight:4.84kg(10.66 lb)
- Insulation class: F
- Waterproof grade: IP65
- Electrical time constant: 4.69ms
- Torque constant: 0.66N.m/A
- Rotor inertia: 0.916x10-3 (kg.m²)
- Back emf: 43V (V/1000r/min)
- Line resistance: 0.55Ω
- Line inductance: 2.58mH
Torque & Speed
- Rated speed: 3000rpm/min
- Rated torque: 5.73N.m
- Max speed: 4000rpm/min
- Max torque: 16.2N.m
Advantages:
1.Matching with 17 bit single coil absolute magnetic encoder, 5 pairs of poles,to ensure the positioning accuracy of one millionth.
2.Standard RS485 communication function, realize upload and download network control.
3.All input/output ports can be freely defined and have strong applicability.
4.Position control, speed control, torque control Modbus;communication can be converted to meet common applications.
5.A variety of intelligent monitoring functions and operation panels are convenient for customers to debug and diagnose.
6.The internal simple PLC function, in some simple control occasions, PLC can be completely omitted, and a lower cost solution can be realized.
- Model: SDF20NK5X
- Maximum current: 18A
- Input voltage: AC170-253V (50Hz or 60Hz)
- Cooling method: radiating air cooling
- Control mode: SVPWM control
- Operating temperature: 0℃~+55℃
- Storage temperature: -20℃-80℃
- Protection level: IP54
- Control model: Position control/speed control/torque control/inching operation/RS485 communication
- Braking function: Built-in
- Display and operation: Six digit seven segment display LED,four function operation
- Protective function: Undervoltage, overvoltage, overload, overcurrent, encoder abnormality, braking, position out of tolerance, etc.
- Command control mode: external pulse
- External command pulse input form: pulse+square, double pulse, A/B quadrature
- Speed control range Speed regulation ratio: 1:5000
SDF series driver position control mode wiring diagram (24V single-ended input signal)
Note:
The functions of input port 1-input port 6 can be defined; please refer to PN1110-PN116 parameters for details.
The function of output port 1-output port 3 can be defined;please refer to PN70-PN72 parameters for details.
Position control model
- Command control model: External pulse
- External command pulse input:
- Form: pulse+ direction cw/ccw A/B orthogonality
- Maximum frequency differential motion: 1MHZ open collector: 200KHZ
- Electronic gear ratio: 1～32767/1～32767
- Speed control range: speed ratio: 1:5000
- Speed rate of change: Speed fluctuation ratio: ＜±0.03(load 0 - 100%) .＜ ±0.05 (power -15% - +10%)
- Command smooth way: Linear time constant 1 ms-10000ms （0r/min←→1000r/min)
- frequency characteristic: 300HZ
Servo driver peripheral devices wiring
Input/output signal:
- location signal output
- output type:ABZ phase line drive output/ Z open collector output
- frequency division ratio: 1/225～1Frequency division
- input signal---7 points photoelectrie isolation input:
- Input point can be defined as any 21kinds, see parameter setting
Output signal 4 collector open
- location/speed reach
- servo alarm output
- Z signal output
- brake output.
Power line terminals wiring
- L1, L2, L3, PE, U, V, W terminal, transversal area≥1.5mm2(AWG14-16). L,N terminal,transversal area≥1.0 mm2(AWG16-18).
- Grounding: the grounding wire should be as thick as possible, drive and servo motor grounding at PE terminal, grounding resistance＜100Ω.
Application areas:
AGV trolley, medical equipment, automatic door, industrial robot, cutting machine, electronic processing and detection,Solid coordinate measuring instrument,CNC gear shaper,CNC hobbing machine,Industrial manipulator,Semiconductor equipment,Engraving equipment,Measuring equipment,Medical equipment,robot and other automated equipment on the market.
Walter
Reviewed in the United States on March 20, 2025
It works very well. I already installed it twice and works fine.
IRV
Reviewed in the United States on August 12, 2024
The drive gives AL03 alarm under very light load even when I connect 750watt servo with it's specs loaded into drive, but 1.5kw motor works on the SDF08NK8X drive which is actually too small for it but it works, this is all wit 240volt mains. When i use 220volt mains it works normal, this is not as the manual shows it can go over 250volt. The dc bus seems to trigger to dump volts to brake resistor even at idle but not with 220volt The other 2x 750watt servo + SDF08NK8X drives work fine
Adan Gtz
Reviewed in Mexico on April 16, 2024
lo instale sin ningún problema. El manual lo descargue de la web. Y lo programe en modo posicion
Bill N
Reviewed in the United States on March 7, 2023
quiet, smooth.
aaron
Reviewed in the United States on September 17, 2022
I'm trying to wire theA + A-B+B-Z+Z-Encoder wires..I think I may have smoked one of my boards...From what I can tell these are outputting around 48 volts ? Is this correct ?I believe my board import pins should be 5 volts for mach 3..If these are 48 volts do I just need to use a resister to drop the voltage to 5 volts ?Overall very happy with this setup ..I have 5 relays wired to mach 3 to control internal settings on the driver...I have puls speed fully controlled by mach 3 0-3000 rpm...a button in mach 3 and a macro I wrote to swap from spindle "rpm" mode to position mode swapping it to c axis for position control "Ridgid tapping" and threading...Very good product and a satisfied buyer..I don't have it on the machine as this is a full build..6 axis with a lathe and auto tool changer build..the macro on that wasn't fun lol
Justin Kwasny
Reviewed in the United States on June 27, 2022
The media could not be loaded.
juliet
Reviewed in the United States on May 9, 2022
I purchased this set to use as spindle drive on a G0704 mill with a centroid acorn board and analog 0-10V. As stated in other reviews there is no autotuning with this drive, it's all by reading the manual and then changing parameters on the control itself. If you have a background in servos this will not be difficult, if you do not then purchasing this unit will give you an education. Much os the manual is vague so I recommend downloading the manual first and reading through it before purchase if you have any doubts. This is a good unit though and I have no issues with it in use.
Alex P.
Reviewed in the United States on February 28, 2022
I used these to upgrade my Index Wells CNC knee mill that had mismatched steppers. These motors are super quiet and have excellent torque - my rapids are now 200ipm (~5000 mm/sec) which is more than enough for my machine. I am sure I can make it go faster, just don't think I should.I really like that these plugged in directly into a Mach3 break out board and I did not need a power supply. Essentially for $300 you are getting a complete axis kit, which is a great deal.The software does not include auto tuning, and seller does not sell the RS485 cable that you would use to connect from the computer. Instead, manual has a whole section on tuning the driver manually. The seller was very helpful and provided instructions that allowed me to build my own USB->Amplifier RS485 cable with which I was able view the run graphs and tune some parameters.After few hours of reading documentation and trial and error, I reached, what I think, excellent results, and quieted the motors at idle. I do wish that auto tuning was available (maybe in new version?)
Thomas
Reviewed in the United States on October 2, 2022
I purchased 3 servo motors with drives. Two 750 watt servos and one 1000 watt servo with brake. One 750 watt and the one 1000 watt servo motors are defective and inoperable due to the drive not seeing the motor encoder. Only one 750 watt servo worked. Do not waste your time on these junk servos. Also no product support or customer service response from the seller. If I could give them a negative five stars I would.I am a very dissatisfied customer.
Recommended Products